Cisco CCNP 300-615 Questions & Answers

• Question 21:

  Refer to the exhibit.

  

  To avoid service disruption, an engineer must move the_ server from LEAF_ 1 to LEAF_ _2. After running the test, the engineer noticed that L EAF_ 2 failed to forward network traffic into the VXL AN fabric. The BGP, interface NVE, and VNI were confirmed to be configured as expected. Which two actions must be taken on L EAF_ 2 to resolve the issue? (Choose two.)

  A. Change the fabric forwarding anycast-gateway-mac MAC address.

  B. Add fabric forwarding mode anycast-gateway on interface Vlan100.

  C. Configure correspondent IP addressing on every interface.

  D. Remove ip forward from interface VIan30 and add it on interface Vlan100.

  E. Enable HMM tracking to advertise host routes into the VXL AN fabric.

  Correct Answer: AE

• Question 22:

  Refer to the exhibit.

  

  A network engineer needs to capture traffic from the VMs that utilize the IOM host interface Eth1/1/23 of a Cisco UCS B-Series chassis. A traffic analyzer is used to get traffic captured from the Eth1/4 interface of the subordinate fabric interconnect. The network engineer notices that traffic is not captured on the traffic analyzer. Which action resolves the issue?

  A. Span the traffic from the Eth 1/2 of the subordinate fabric interconnect

  B. Span the traffic from the Eth 1/2 of the primary fabric interconnect

  C. Span the traffic from the Eth 1/4 of the subordinate fabric interconnect

  D. Span the traffic from the Eth 1/4 of the primary fabric interconnect

  Correct Answer: B

• Question 23:

  Refer to the exhibit.

  

  A network engineer is implementing a pair of Cisco Nexus 9000 Series Switches. During the OSPF configuration, the engineer discovers unstable routing in the network. The investigation shows flapping routes after the new switches were introduced. Which set of actions resolves the issue?

  A. Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF process.

  B. Configure a new IP address on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.

  C. Configure a new OSPF priority on the Ethernet interface toward the OSPF neighbor. Clear the OSPF neighbor.

  D. Configure a new IP address on the Loopback interface toward the OSPF process. Clear the OSPF process.

  Correct Answer: C

• Question 24:

  Refer to the exhibit.

  

  A certificate is implemented on the security configuration on the Cisco ACI controller. A customer receives a "Connection Not Secure" error in a browser every time the customer logs in to the Cisco APIC GUI. Which action resolves the issue?

  A. Include a private key with the certificate.

  B. Use a browser that supports keys of 2048 bits.

  C. Configure a corporate certificate authority for the certificate.

  D. Add a 1536-bit key to the APIC GUI.

  Correct Answer: C

• Question 25:

  Refer to the exhibit.

  

  A blade that is connected to FI-A fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA0 as the SAN Primary. Which set of actions resolves the issue?

  A. Change Adapter Policy to VMWare on vHBA0

  B. Change vHBA0 to VSAN 11 in Service Profile

  C. Configure vHBA_SAN_A zone to VSAN 10

  D. Set VSAN to 11 in vHBA_SAN_

  Correct Answer: B

• Question 26:

  A network engineer experiences the error "DDR3_P1_B1_ECC" when upgrading Cisco UCS firmware. Which action resolves the issue?

  A. Reset the DIMM

  B. Reset the BMC firmware

  C. Reflash the controller firmware

  D. Reflash the DIMM

  Correct Answer: A

• Question 27:

  Refer to the exhibit.

  

  A client reports that the routing protocol neighborship fails to start between two Cisco Nexus switches, N9K-1 and N9K-2. Which action resolves the issue?

  A. Add OSPF routing configuration to interface e1/1 on both Cisco Nexus switches

  B. Configure a unicast access list to allow the negotiation between N9K-1 and N9K-2

  C. Configure a multicast access list to allow the negotiation between N9K-1 and N9K-2

  D. Add MTU configuration to interface e1/1 on both Cisco Nexus switches

  Correct Answer: B

• Question 28:

  Refer to the exhibit.

  

  A network engineer finds one of the fabric interconnects offline when connecting L1 and L2 ports on both fabric interconnects. Which action resolves the issue?

  A. 1. Connect to Fabric Interconnect B.

  2.

  Verify the cluster status and HA election.

  3.

  Validate Fabric Interconnect B hardware issues.

  B. 1. Connect to Fabric Interconnect A.

  2.

  Verify the cluster status and HA election.

  3.

  Validate Fabric Interconnect A hardware issues.

  C. 1. Connect Fabric Interconnect B and change the role to primary.

  2.

  Reboot Fabric Interconnect B.

  3.

  Add the Fabric Interconnect A as subordinate fabric to the cluster.

  D. 1. Connect Fabric Interconnect B and execute "Erase configuration"

  2.

  Reboot Fabric Interconnect B.

  3.

  Add the subordinate Fabric Interconnect to the cluster.

  Correct Answer: D

• Question 29:

  Refer to the exhibit.

  

  

  A network engineer must use BGP to route IPv4 and IPv6 routes between R1 and R2. The IPv4 addresses are exchanged as expected between the routers through BGP. The routers have reached an Established BGP state. However, the IPv6 routes from R2 fail to show in the routing table of R1. Which action resolves the issue?

  A. Create a route map that sets the IPv6 next hop.

  B. Advertise L2VPN EVPN under IPv4 unicast address family

  C. Configure an IPv6 BGP neighbor on R1

  D. Enable IPv6 routing on R1

  Correct Answer: A

• Question 30:

  An engineer upgrades Cisco UCS firmware from release 3.1(2) to release 3.1(3) using AutoInstall. Both fabric interconnects go offline during the software upgrade installation and issue multiple FSM retries in the DeployPollActivate stage. Which set of actions resolves the issue?

  A. Clear the startup version of the default infrastructure and server pack. Remove the service pack from the subordinate node. Upgrade with the Force attribute through AutoInstall.

  B. Enable the management interface monitoring policy on the fabric interconnects. Initiate a configuration backup on both fabric interconnects. Commit the pending fabric interconnect reboot activity.

  C. Fix the rights to 666 with the debug plugin on the primary fabric interconnect. Save the current configuration on the running fabric interconnect. Continue the upgrade on both fabric interconnects.

  D. Acknowledge the error and reboot the primary fabric interconnect. Clear the default firmware version and upload a new one. Restart the upgrade process manually.

  Correct Answer: A