Cisco 200-401 Online Practice Questions and Exam Preparation

Cisco 200-401 Online Questions & Answers

• Question 51:

  Which two pieces of information are commonly tracked as part of a change management process? (Choose two.)

  A. reason for the change
  B. names of people involved in the change
  C. return on investment related to the change
  D. SWOT analysis related to the change
  E. scatter diagrams related to the change
  A. reason for the change
  B. names of people involved in the change

• Question 52:

  At which Layer would you check for spanning tree loops?

  A. Layer 1
  B. Layer 2
  C. Layer 3
  D. Layer 4
  B. Layer 2

• Question 53:

  With a Cisco IE 2000 switch, what does a power status LED indicate when it is solid green?

  A. Power is present on the associated circuit and the system is operating normally.
  B. Power is present on the associated circuit, but there is no correlation to whether the system is operating normally.
  C. The system is operating normally, but power is not necessarily present on the associated circuit.
  D. Power is not present on the associated circuit and the power supply alarm is configured.
  E. The power status LED does not show solid green.
  A. Power is present on the associated circuit and the system is operating normally.

• Question 54:

  An Ethernet cable is attached to a PC NIC and then attached to a switch port. The PC power is turned on and the switch port link LED turns green. The link light indicates what two conditions? (Choose two.)

  A. Layer 2 communication has been established between the PC and switch.
  B. The PC has received a DHCP address.
  C. Traffic is being sent from the switch to the PC.
  D. If flashing, the green LED indicates port speed of 100 Mb/s.
  E. The Layer 1 media is functioning between the PC and switch.
  F. The switch port is functioning as a half-duplex connection.
  A. Layer 2 communication has been established between the PC and switch.
  E. The Layer 1 media is functioning between the PC and switch.

• Question 55:

  A small manufacturing company has a Class C network address on the plant floor and needs to create five subnets, each accommodating 25 endpoints. Which subnet mask needs to be configured?

  A. 255.255.240.0
  B. 255.255.255.128
  C. 255.255.255.192
  D. 255.255.255.224
  E. 255.255.255.240
  F. 255.255.255.248
  D. 255.255.255.224

• Question 56:

  Which parameter would you tune to affect the selection of a static route as a backup, when a dynamic protocol is also being used?

  A. hop count
  B. administrative distance
  C. link bandwidth
  D. link delay
  E. link cost
  B. administrative distance

• Question 57:

  Exhibit:

  

  Which two statements are correct for a safe wiring installation to the terminal block of the switch or endpoint? (Choose two.)

  A. Insert a green ground wire into the terminal block that is marked RT for return.
  B. Verify that DC power is live and within 24 VDC voltage range before starting wiring.
  C. Verify that the DC power circuit includes an overcurrent protective device that limits the DC current to 5
  E. Because this is a low-voltage DC circuit, anyone can install this wiring without electrical training or qualifications.
  F. Connect the positive 24 VDC conductor to the V terminal and connect the negative 24 VDC return wire to the RT terminal.
  G. A ground wire can optionally be connected to the screw terminal on the front of the switch.
  C. Verify that the DC power circuit includes an overcurrent protective device that limits the DC current to 5
  E. Because this is a low-voltage DC circuit, anyone can install this wiring without electrical training or qualifications.

• Question 58:

  Exhibit: Refer to the exhibit. An industrial ruggedized network device needs to be installed in the place of the icon labeled Network Device to accommodate a leased line attachment to the Internet. Which network device and interface configuration meets the minimum requirements for this installation?

  

  A. a router with two Ethernet interfaces
  B. a switch with two Ethernet interfaces
  C. a router with one Ethernet and one serial interface
  D. a switch with one Ethernet and one serial interface
  E. a router with one Ethernet and one modem interface
  C. a router with one Ethernet and one serial interface

• Question 59:

  A network administrator has subnetted the 172.16.0.0 network using a subnet mask of 255.255.255.192. A duplicate IP address of 172.16.2.120 has accidentally been configured on a workstation in the network. The technician on the plant floor must assign this workstation a new IP address within that same subnetwork. Which address should be assigned to the workstation?

  A. 172.16.1.80
  B. 172.16.2.80
  C. 172.16.1.64
  D. 172.16.2.64
  E. 172.16.2.127
  F. 172.16.2.128
  B. 172.16.2.80

• Question 60:

  Which option best describes a mechanical, ingress, climatic, chemical and electromagnetic environment that is classified as M3 I3 C3 E3?

  A. the highest quality
  B. office environment
  C. severe
  D. serviced by multiple cable segments
  C. severe