Cisco 200-401 Online Practice Questions and Exam Preparation

Cisco 200-401 Online Questions & Answers

• Question 31:

  With a Cisco IE 2000 switch, what does a port status LED indicate when it is solid amber?

  A. The port is sending or receiving data.
  B. A link is present.
  C. No link is present.
  D. There is a link fault.
  E. The port is not forwarding.
  E. The port is not forwarding.

• Question 32:

  A router is not operating as expected and the network administrator wants to verify that the router booted using the correct IOS image. Which command should be used to determine which IOS is running on the router?

  A. show flash
  B. show version
  C. show memory
  D. show startup-config
  E. show config-register
  B. show version

• Question 33:

  Exhibit:

  

  Refer to the exhibit. The output that is shown is generated at an industrial switch. Which three statements are true? (Choose three.)

  A. All ports will be in a state of discarding, learning, or forwarding.
  B. Thirty VLANs have been configured on this switch.
  C. The bridge priority is lower than the default value for spanning tree.
  D. All interfaces that are shown are on shared media.
  E. All designated ports are in a forwarding state.
  F. This switch must be the root bridge for all VLANs on this switch.
  A. All ports will be in a state of discarding, learning, or forwarding.
  C. The bridge priority is lower than the default value for spanning tree.
  E. All designated ports are in a forwarding state.

• Question 34:

  Which three of the following components must be elected before the Spanning Tree Protocol can converge in a switched LAN? (Choose three.)

  A. designated ports
  B. duplex operating mode
  C. fast mode ports
  D. root bridge
  E. root ports
  F. BDPU priority
  A. designated ports
  D. root bridge
  E. root ports

• Question 35:

  EtherNet/IP is an Ethernet implementation of which protocol?

  A. CIP
  B. Industrial Protocol
  C. DeviceNet
  D. ControlNet
  A. CIP

• Question 36:

  Which two reasons make mesh bonding systems most effective? (Choose two.)

  A. cover wide areas
  B. provide additional strength to floor structures
  C. provide low-impedance noise-equalizing paths
  D. create equipotential grounding systems
  E. most cost-effective approach
  C. provide low-impedance noise-equalizing paths
  D. create equipotential grounding systems

• Question 37:

  What should be done with unused conductors in copper unshielded or shielded twisted-pair network cables?

  A. terminate in their characteristic impedance
  B. trim back and properly insulate
  C. connect to protective earth
  D. splice to a used conductor
  A. terminate in their characteristic impedance

• Question 38:

  What is a reason to use user EXEC mode on an industrial switch?

  A. to verify commands that you have entered
  B. to change terminal settings
  C. to configure VLAN parameters
  D. to configure parameters that apply to the entire switch
  B. to change terminal settings

• Question 39:

  At which Layer would you troubleshoot a cabling issue?

  A. Layer 1
  B. Layer 2
  C. Layer 3
  D. Layer 4
  A. Layer 1

• Question 40:

  Which of the following correctly pairs the dotted decimal subnet mask with the correct number of binary bits that represent the subnet mask?

  A. 255.255.255.192 and /25
  B. 255.255.255.248 and /28
  C. 255.255.255.224 and /26
  D. 255.255.255.248 and /27
  E. 255.255.255.240 and /28
  F. 255.255.255.240 and /16
  E. 255.255.255.240 and /28