Cisco 200-401 Online Practice Questions and Exam Preparation

Cisco 200-401 Online Questions & Answers

• Question 41:

  For which three issues should fiber-optic network segments be tested? (Choose three.)

  A. attenuation
  B. near-end crosstalk
  C. length
  D. polarity
  E. jitter
  F. tensile stress
  A. attenuation
  C. length
  D. polarity

• Question 42:

  Which two ports does EtherNet/IP use to communicate? (Choose two.)

  A. TCP 44818
  B. UDP 44818
  C. TCP 502
  D. UDP 502
  E. TCP 2222
  F. UDP 2222
  A. TCP 44818
  F. UDP 2222

• Question 43:

  Why is SSH preferred over Telnet as a method of accessing a network device to alter or view the configuration?

  A. Telnet encrypts only the login information, not the entire transmission.
  B. SSH requires fewer network resources and no additional configuration.
  C. Telnet is more difficult to use and configure than SSH.
  D. SSH encrypts the login and session information.
  D. SSH encrypts the login and session information.

• Question 44:

  The network administrator is using a Windows PC application that is called putty.exe for remote communication to a switch for network troubleshooting. Which two protocols could be used during this communication? (Choose two).

  A. SNMP
  B. HTTP
  C. Telnet
  D. RMON
  E. SSH
  C. Telnet
  E. SSH

• Question 45:

  Exhibit:

  

  Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

  A. These commands need to be added to the configuration:C-router(config)# router eigrp 123C- router (config-router)# network 172.19.0.0
  B. These commands need to be added to the configuration:C-router(config)# router ospf 1C- router (config-router)# network 172.19.0.0 0.0.3.255 area 0
  C. These commands need to be added to the configuration:C-router(config)# router ripC-router(config- router)# network 172.19.0.0
  D. No further routing configuration is required.
  D. No further routing configuration is required.

• Question 46:

  Which option allows an EtherNet/IP I/O device to be safely installed where it is subject to water immersion?

  A. The device is rated IP20 and the power wiring is installed securely to the terminal block.
  B. The device is rated IP67 and a power cordset is used.
  C. The device is rated IP67 and immersed to 10 m.
  D. The device is rated IP20 and immersed to 10 m.
  B. The device is rated IP67 and a power cordset is used.

• Question 47:

  What is a reason to use privileged EXEC mode on an industrial switch?

  A. to verify commands that you have entered
  B. to change terminal settings
  C. to configure VLAN parameters
  D. to configure parameters that apply to the entire switch
  A. to verify commands that you have entered

• Question 48:

  DRAG DROP

  Select and Place:

  

  

• Question 49:

  What are two recommended tools or commands that allow you to troubleshoot connectivity between two devices in different IP networks? (Choose two.)

  A. show interface status
  B. show spanning-tree
  C. ping
  D. show interfaces gigabitEthernet x/y switchport
  E. traceroute
  F. show interface
  C. ping
  E. traceroute

• Question 50:

  What is the leading cause of fiber-optic link failure?

  A. contaminants
  B. crushed fiber
  C. poor testing practices
  D. bad connectors
  A. contaminants