Cisco 200-401 Online Practice Questions and Exam Preparation

Cisco 200-401 Online Questions & Answers

• Question 1:

  Exhibit:

  

  Refer to the exhibit. Host 3 on Network A is sending data to Host 8 on Network B. Which address is the default gateway of Host 3?

  A. the address of the switch interface that is connected to router interface Fa0/0
  B. the address of the switch interface that is connected to router interface Fa0/1
  C. the address of the host that is connected to Network A
  D. the address of the host that is connected to Network B
  E. the address of the router interface Fa0/0
  F. the address of the router interface Fa0/1
  E. the address of the router interface Fa0/0

• Question 2:

  What do deflections indicate to the time domain reflectometer user?

  A. They indicate splices, water in the cable, split pairs, and discontinuities or faults.
  B. Do not connect live circuit cables to the input of the time domain reflectometer. Connect the cable that is being tested to the cable connector on the front panel of the time domain reflectometer.
  C. Upward deflections indicate high-impedance mismatches or opens, and downward deflections indicate shorts or low-impedance mismatches.
  D. They are used to select the I/O impedance of the time domain reflectometer. You can select 50, 75, 95, or 125? impedances.
  C. Upward deflections indicate high-impedance mismatches or opens, and downward deflections indicate shorts or low-impedance mismatches.

• Question 3:

  Which two commands can help you to determine what image is running on your industrial switch? (Choose two.)

  A. show version
  B. show spanning-tree
  C. show interface-switch
  D. show interfaces gigabitEthernet x/y switchport
  E. show license
  A. show version
  E. show license

• Question 4:

  What does the Cisco PSIRT issue for significant security issues that directly involve Cisco products and require an upgrade, fix, or other customer action?

  A. Cisco Security Advisories
  B. Cisco Security Responses
  C. Cisco Security Notices
  D. Cisco Security Bulletins
  A. Cisco Security Advisories

• Question 5:

  What is a characteristic of cables that are used in articulating equipment arms?

  A. fiber-optic zip-cord construction
  B. shielded copper twisted pair
  C. high flex rated cable
  D. type PLTC cable
  C. high flex rated cable

• Question 6:

  What are two symptoms of duplex mismatch? (Choose two.)

  A. Ping does not return from one direction versus the other direction.
  B. Communication is slow and locks up.
  C. Speed is seen equally slow in both directions.
  D. The half-duplex side sees frame sequence errors or runt frames.
  E. The full-duplex side sees CRC errors.
  B. Communication is slow and locks up.
  D. The half-duplex side sees frame sequence errors or runt frames.

• Question 7:

  What is the most critical step to perform when you are using optical fiber connectors?

  A. Cover with dust caps when not in use.
  B. Immerse in alcohol prior to use.
  C. Blow off and carefully wipe down with a tissue before and after each use.
  D. Lightly sand with cloth prior to mating.
  A. Cover with dust caps when not in use.

• Question 8:

  At which Layer would you use trace route to validate the path?

  A. Layer 1
  B. Layer 2
  C. Layer 3
  D. Layer 4
  C. Layer 3

• Question 9:

  How does the optical time domain reflectometer use "backscattered" light to make measurements?

  A. It uses pulses to locate and test for sheath faults, damaged conductors, loose connectors, splices, bridge taps, split pairs, and other problems.
  B. It performs wiremapping to measure that all pins are correctly connected.
  C. It correlates the returned light pulses with a location in the fiber.
  D. It measures light-pulse width to measure that all pins are correctly connected.
  C. It correlates the returned light pulses with a location in the fiber.

• Question 10:

  Exhibit:

  

  Refer to the exhibit. CCNA.com has the industrial network shown in the exhibit. All switches are configured as layer 2 switches and are using VLAN 1 as their management VLAN. Each VLAN 1 interface has been assigned the correct IP address. What is the purpose of assigning a default gateway to SW-C switch?

  A. allows connectivity between the VLAN 1 interface on SW-C and other devices in the network.
  B. allows connectivity between Host A and other devices in the network.
  C. allows connectivity between Host B and other devices in the network.
  D. allows the switch to pass traffic between Host A and Host B
  A. allows connectivity between the VLAN 1 interface on SW-C and other devices in the network.