Cisco 200-105 Online Practice Questions and Exam Preparation

Cisco 200-105 Online Questions & Answers

• Question 581:

  What does the frame-relay interface-dlci command configure?

  A. local DLCI on the subinterface
  B. remote DLCI on the main interface
  C. remote DCLI on the subinterface
  D. local DLCI on the main interface
  A. local DLCI on the subinterface

  ---

  Frame Relay for ICND Exam To assign a data-link connection identifier (DLCI) to a specified Frame Relay subinterface on the router or access server, or to assign a specific permanent virtual circuit (PVC) to a DLCI, or to apply a virtual template configuration for a PPP session, use the frame-relay interface-dlci interface configuration command. Example 4-23 Example of frame-relay interface-dlci Command and the Output of show frame-relay map R4(config)#interface s1/2.403 point-to-point R4(config-subif)#frame-relay interface-dlci ? <16-1007> Define a switched or locally terminated DLCI R4(config-subif)#frame-relay interface-dlci 403 ? cisco Use CISCO Encapsulation ietf Use RFC1490/RFC2427 Encapsulation ppp Use RFC1973 Encapsulation to support PPP over FR protocol Optional protocol information for remote end R4#show frame-relay map Serial1/2.403 (up): point-to-point dlci, dlci 403(0xC9,0x3090), broadcast status defined, active R4#

  Reference: http://www.ciscopress.com/articles/article.asp?p=100603andseqNum=3

• Question 582:

  In which configuration can a PPPoE client operate normally?

  A. on a dialer interface configured with multilink PPP
  B. on a CPE with more than 10 other clients
  C. on an Ethernet connection between two endpoints
  D. on a dialer interface configured for QoS queuing
  A. on a dialer interface configured with multilink PPP

• Question 583:

  By default, which two K values does EIGRP for IPv6 use to calculate the metric? (Choose two.)

  A. reliability
  B. bandwidth
  C. load
  D. MTU
  E. delay
  B. bandwidth
  E. delay

• Question 584:

  Instructions

  This item contains several questions that you must answer. You can view these questions by clicking on the corresponding button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In

  order to complete the questions, you will need to refer to the topology.

  To gain access to the topology, click on the topology button at the bottom of the screen. When you have finished viewing the topology, you can return to your questions by clicking on the Questions button to the left.

  Each of the windows can be minimized by clicking on the [-]. You can also reposition a window by dragging it by the title bar.

  Scenario

  Refer to the topology. Using the information shown, answer the four questions shown on the Questions tab.

  

  R1 is configured with the default configuration of OSPF.

  From the following list of IP addresses configured on R1, which address will the OSPF process select as the router ID?

  A. 192.168.0.1
  B. 172.16.1.1
  C. 172.16.2.1
  D. 172.16.2.225
  A. 192.168.0.1

  ---

  The Router ID (RID) is an IP address used to identify the router and is chosen using the following sequence:

  +

  The highest IP address assigned to a loopback (logical) interface.

  +

  If a loopback interface is not defined, the highest IP address of all active router's physical interfaces will be chosen.

  +

  The router ID can be manually assigned

  In this case, because a loopback interface is not configured so the highest active IP address 192.168.0.1 is chosen as the router ID.

• Question 585:

  A network administrator has configured access list 173 to prevent Telnet and ICMP traffic from reaching a server with the address of 192.168.13.26.

  Which commands can the administrator issue to verify that the access list is working properly? (Choose three.)

  A. Router# ping 192.168.13.26
  B. Router# debug access-list 173
  C. Router# show open ports 192.168.13.26
  D. Router# show access-lists
  E. Router# show ip interface
  A. Router# ping 192.168.13.26
  D. Router# show access-lists
  E. Router# show ip interface

• Question 586:

  Which feature or value must be configured to enable EIGRPv6?

  A. Network statement
  B. Shutdown feature
  C. Router ID
  D. Remote AS
  C. Router ID

  ---

  The configuration of EIGRP for IPv6 has some restrictions; which are:

  The interfaces can be directly configured with EIGRP for IPv6, without the use of a global IPv6 address. There is no network statement in EIGRP for IPv6.

  The router ID needs to be configured for an EIGRPv6 protocol instance before it can run.

  EIGRP for IPv6 has a shutdown feature. Ensure that the routing process is in "no shut" mode in order to run the protocol.

  Reference: https://www.cisco.com/c/en/us/support/docs/ip/enhanced-interior-gateway-routing-protocol-eigrp/113267-eigrp-ipv6-00.html

• Question 587:

  Which options are the two differences between HSRP versions 1 and 2? (Choose two.)

  A. Only HSRP version 2 can be configured to use authentication.
  B. Only HSRP version 2 sends hello packets to 224.0.0.2.
  C. Only HSRP version 1 sends hello packets to IPv6 multicast address FF02::66.
  D. Only HSRP version 1 can be configured with a group number of 4095.
  E. Only HSRP version 2 can be configured with a group number of 4095.
  F. Only HSRP version 2 sends hello packets to 224.0.0.102.
  E. Only HSRP version 2 can be configured with a group number of 4095.
  F. Only HSRP version 2 sends hello packets to 224.0.0.102.

  ---

  HSRP version 2 is designed to address the following restrictions in HSRP version 1:

  In HSRP version 1, millisecond timer values are not advertised or learned. HSRP version 2 advertises and learns millisecond timer values. This change ensures stability of the HSRP groups in all cases.

  In HSRP version 1, group numbers are restricted to the range from 0 to 255. HSRP version 2 expands the group number range from 0 to 4095.

  HSRP version 2 provides improved management and troubleshooting. With HSRP version 1, you cannot use HSRP active hello messages to identify which physical router sent the message because the source MAC address is the HSRP

  virtual MAC address. The HSRP version 2 packet format includes a 6-byte identifier field that is used to uniquely identify the sender of the message. Typically, this field is populated with the interface MAC address. The multicast address

  224.0.0.2 is used to send HSRP hello messages. This address can conflict with Cisco Group Management Protocol (CGMP) leave processing.

  Version 1 is the default version of HSRP.

  HSRP version 2 uses the new IP multicast address 224.0.0.102 to send hello packets instead of the multicast address of 224.0.0.2, used by HSRP version 1. This new multicast address allows CGMP leave processing to be enabled at the

  same time as HSRP.

  HSRP version 2 permits an expanded group number range, 0 to 4095, and consequently uses a new MAC address range 0000.0C9F.F000 to 0000.0C9F.FFFF. The increased group number range does not imply that an interface can, or

  should, support that many HSRP groups. The expanded group number range was changed to allow the group number to match the VLAN number on subinterfaces.

  When the HSRP version is changed, each group will reinitialize because it now has a new virtual MAC address.

  HSRP version 2 has a different packet format than HSRP version 1. The packet format uses a type-length-value (TLV) format. HSRP version 2 packets received by an HSRP version 1 router will have the type field mapped to the version field

  by HSRP version 1 and subsequently ignored.

• Question 588:

  What is the first step you perform to configure an SNMPv3 user?

  A. Configure server traps.
  B. Configure the server group.
  C. Configure the server host.
  D. Configure the remote engine ID.
  B. Configure the server group.

  ---

  To configure an SNMP server user, specify an SNMP group or a table that maps SNMP users to SNMP views. Then, specify the IP address or port number for the remote SNMP agent of the device where the user resides. Also, before you configure remote users for a particular agent, configure the SNMP engine ID by using the snmp-server engineID command for the remote agent. The SNMP engine ID of the remote agent is required to compute the authentication or privacy digests for the SNMP password. If the remote engine ID is not configured first, the configuration command will fail.

  SUMMARY STEPS

  1.

  enable

  2.

  configure terminal

  3.

  snmp-server group [group-name {v1 | v2c | v3 [auth | noauth | priv]}] [read read-view] [writewrite-view] [notify notify-view] [access access-list]

  4.

  snmp-server engineID {local engine-id | remote ip-address [udp-port udp-port-number] [vrfvrf-name] engine-id-string}

  5.

  snmp-server user user-name group-name [remote ip-address [udp-port port]] {v1 | v2c | v3[encrypted] [auth {md5 | sha} auth-password]} [access access-list]

  6.

  end

  Reference: https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/snmp/configuration/xe-3se/3850/snmp-xe-3se-3850-book/nm-snmp-snmpv3.html#GUID-E9B523ED-2DEE-44AE-BBEC-ABE75EF40B2A

• Question 589:

  Which two statements about traffic shaping are true? (Choose two.)

  A. It can be applied in the outbound direction only.
  B. Packets that exceed the configured threshold are remarked and sent.
  C. Packets that exceed the configured threshold are held in a buffer.
  D. It can be applied in the inbound and outbound directions.
  E. Packets that exceed the configured threshold are dropped
  A. It can be applied in the outbound direction only.
  C. Packets that exceed the configured threshold are held in a buffer.

• Question 590:

  How can you disable DTP on a switch port?

  A. Configure the switch port as a trunk.
  B. Add an interface on the switch to a channel group.
  C. Change the operational mode to static access.
  D. Change the administrative mode to access.
  D. Change the administrative mode to access.

  ---

  Switchport Mode Access: This puts the interface (ACCESS PORT) into a PERMANENT NON-TRUNKING mode and negotiates to convert the link into a NON-TRUNK link. The port would be a dedicated Layer 2 access port! Switchport Nonegotiates: Prevents the interface from generating DTP Frames. You can use this command only when the interface switchport mode is (ACCESS/TRUNK).