Cisco 200-105 Online Practice Questions and Exam Preparation

Cisco 200-105 Online Questions & Answers

• Question 211:

  On which layer tcp/ip is ACL Apic-EM path?

  A. Layer 1
  B. Layer 2
  C. Layer 3
  D. Layer 4
  D. Layer 4

• Question 212:

  Which two statements about configuring a PPP connection between two routers using CHAP authentication are true? (Choose two.)

  A. Each router can have a different password.
  B. Each router can have a different username.
  C. Each router's username must be the same as its hostname.
  D. Each router must have the same username.
  E. Each router must have the same password.
  B. Each router can have a different username.
  E. Each router must have the same password.

• Question 213:

  Which port type is used in a stacked deployment?

  A. StackWise ports
  B. uplinks
  C. Ethernet ports
  D. console ports
  A. StackWise ports

• Question 214:

  Which configuration command can u apply to a HSRP router so that its local interface becomes active if all other routers in the group fail?

  A. no additional config is required
  B. standby 1 track ethernet
  C. standby 1 preempt
  D. standby 1 priority 250
  A. no additional config is required

• Question 215:

  Which programming language do you use to script interactions between Cisco devices and network controllers such as APIC-EM?

  A. POSIX
  B. Python
  C. Java
  D. C++
  B. Python

• Question 216:

  Which two statements about the BGP network command are true? (Choose two.)

  A. It must be configured to enable BGP between neighbors
  B. It references a connected interface
  C. It must match the subnet and mask of a route in the routing table
  D. It references the routing table
  E. It can specify a different subnet mask than the mask configured on the interface
  C. It must match the subnet and mask of a route in the routing table
  D. It references the routing table

• Question 217:

  Refer to the exhibit. The show interfaces serial 0/1 command was issued on the R10-1 router. Based on the output displayed which statement is correct?

  

  A. The cable connected to the serial 0/1 interface of the R1-1 router is a DTE cable.
  B. The R10-1 router can ping the router interface connected to the serial 0/1 interface.
  C. The clock rate used for interface serial 0/1 of the R10-1 router is 1,544,000bits per second.
  D. The CSU used with the serial 0/1 interface of the R10-1 router has lost connection to the service provider.
  E. The interface of the remote router connected to the serial 0/1 interface of the R10-1 router is using the default serial interface encapsulation.
  E. The interface of the remote router connected to the serial 0/1 interface of the R10-1 router is using the default serial interface encapsulation.

  ---

  Cisco High-Level Data Link Controller (HDLC) is the Cisco proprietary protocol for Cisco HDLC is the default encapsulation type for the serial interfaces.

• Question 218:

  Which configuration do you apply to an HSRP router so that it is most likely to come up if the active router goes down?

  A. Standby 4 preempt
  B. Standby 4 priority 110 preempt delay 300
  C. Standby 4 priority 115
  D. Standby 4 priority 145
  A. Standby 4 preempt

• Question 219:

  Which two functions are performed by DHCP snooping? (Choose two.)

  A. It determines which DHCP messages are valid
  B. It hands out DHCP IP addresses to clients requesting access to the network
  C. It rate-limits certain traffic
  D. It listens to multicast traffic to support packet forwarding
  E. It propagates VLAN information between switches
  F. It provides DDoS mitigation
  A. It determines which DHCP messages are valid
  C. It rate-limits certain traffic

• Question 220:

  Which three statements about the features of SNMPv2 and SNMPv3 are true? (Choose three.)

  A. SNMPv3 enhanced SNMPv2 security features.
  B. SNMPv3 added the Inform protocol message to SNMP.
  C. SNMPv2 added the Inform protocol message to SNMP.
  D. SNMPv3 added the GetBulk protocol messages to SNMP.
  E. SNMPv2 added the GetBulk protocol message to SNMP.
  F. SNMPv2 added the GetNext protocol message to SNMP.
  A. SNMPv3 enhanced SNMPv2 security features.
  C. SNMPv2 added the Inform protocol message to SNMP.
  E. SNMPv2 added the GetBulk protocol message to SNMP.