Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 531:

  Which configuration parameter allows a Junos device to include an interface route into OSPF while prohibiting adjacencies from forming?

  A. inactive
  B. no-peer-advertise
  C. disable
  D. passive
  D. passive

• Question 532:

  Which statement is true about the operation of a Layer 2 VPN?

  A. The service provider will use a routing protocol from the PE to CE
  B. A Layer 2 VPN transports packets based on Data Link Layer headers
  C. Layer 2 VPNs cannot transport Layer 3 protocol information
  D. VPN signaling will be performed by RSVP
  B. A Layer 2 VPN transports packets based on Data Link Layer headers

• Question 533:

  For two switches to participate in the same Multiple Spanning Tree Protocol (MSTP) region, which three values must match? (Choose three.)

  A. extended system ID
  B. region name
  C. member VLAN ID list
  D. root bridge ID
  E. revision number
  A. extended system ID
  C. member VLAN ID list
  E. revision number

• Question 534:

  Which role does the router ID (RID) have in the BGP route selection process?

  A. The router ID is evaluated immediately after MED to determine route preference
  B. The router ID is evaluated last in the route selection process
  C. The router ID is evaluated after the cluster length and a lower router ID is chosen
  D. The router ID is evaluated after analyzing the IGP metric cost
  C. The router ID is evaluated after the cluster length and a lower router ID is chosen

• Question 535:

  What are two destination addresses used for OSPF link-state update packets? (Choose two.)

  A. 224.0.0.1
  B. 224.0.0.4
  C. 224.0.0.6
  D. 224.0.0.5
  C. 224.0.0.6
  D. 224.0.0.5

• Question 536:

  What does an STP BPDU Port ID field contain?

  A. bridge priority
  B. bridge port priority and bridge port address
  C. bridge priority and bridge address
  D. port priority and port address
  D. port priority and port address

• Question 537:

  Which command verifies that graceful Routing Engine Switchover (GRES) is operational?

  A. show system switchover on the master RE
  B. show system switchover on the backup RE
  C. show task replication on the master RE
  D. show task replication on the backup RE
  B. show system switchover on the backup RE

• Question 538:

  You are logged into a router and have navigated to the [edit routing-options] level of the hierarchy. You have been asked to define an aggregate route for 172.30/16. Which command correctly configures this setup?

  A. set summary route 172.30/16
  B. set aggregate route 172.30/16
  C. set route aggregate 172.30/16
  D. set route summary 172.30/16
  B. set aggregate route 172.30/16

• Question 539:

  An RSVP LSP in your network is not operational and you suspect that the "family mpls" statement was omitted from the device configuration. Which operational mode command will help you to verify your suspicions?

  A. show interface terse
  B. show mpls lsp
  C. show rsvp session
  D. show rsvp interface
  A. show interface terse

• Question 540:

  -- Exhibit -[edit policy-options]

  user@router# show

  policy-statement load-balance {

  from {

  route-filter 10.243.0.0/24 exact;

  route-filter 10.224.1.0/24 exact;

  }

  then {

  load-balance per-packet;

  }

  }

  -- Exhibit -

  Click the Exhibit button.

  You have been asked to configure per-packet load balancing.

  Referring to the exhibit, which configuration correctly applies the load-balancing policy?

  A. [edit routing-options] user@router# show forwarding-options { export load-balance; }
  B. [edit routing-options] user@router# show static { export load-balance; }
  C. [edit routing-options] user@router# show forwarding-table { export load-balance; }
  D. [edit routing-options] user@router# show routing-table { export load-balance; }
  C. [edit routing-options] user@router# show forwarding-table { export load-balance; }