Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 1:

  Which three statements are true about BGP default operations? (Choose three.)

  A. IBGP peers advertise routes received from EBGP peers to other IBGP peers.
  B. IBGP peers do not advertise routes received from IBGP peers to other IBGP peers.
  C. IBGP peers do not advertise routes received from EBGP peers to other IBGP peers.
  D. IBGP peers change the next hop for routes received from EBGP peers.
  E. EBGP peers advertise routes learned from IBGP or EBGP peers to other EBGP peers.
  A. IBGP peers advertise routes received from EBGP peers to other IBGP peers.
  B. IBGP peers do not advertise routes received from IBGP peers to other IBGP peers.
  E. EBGP peers advertise routes learned from IBGP or EBGP peers to other EBGP peers.

• Question 2:

  You have been asked to provision a service provider's network to accommodate Layer 3 VPNs as defined in RFC 4364. Which three tasks must be performed before the provider network is ready to carry VPN traffic? (Choose three.)

  A. All Juniper Networks PE routers must be configured with an appropriate router-ID unique to the VPN.
  B. All Juniper Networks PE routers must be configured with an appropriate route-target unique to the VPN.
  C. All Juniper Networks PE routers must be configured with a routing-instance of type forwarding.
  D. All Juniper Networks PE routers must be configured with a routing-instance of type vrf.
  E. All Juniper Networks PE routers must be configured with a routing-instance containing the CE-facing interface.
  B. All Juniper Networks PE routers must be configured with an appropriate route-target unique to the VPN.
  D. All Juniper Networks PE routers must be configured with a routing-instance of type vrf.
  E. All Juniper Networks PE routers must be configured with a routing-instance containing the CE-facing interface.

• Question 3:

  Which statement is true of a Layer 2 circuit?

  A. Layer 2 circuits use BGP for signaling
  B. Layer 2 circuits use OSPF for signaling
  C. Layer 2 circuits use LDP for signaling
  D. Layer 2 circuits rely on RSVP for signaling
  C. Layer 2 circuits use LDP for signaling

• Question 4:

  Which two events could cause the BGP Active state to appear? (Choose two.)

  A. The local router does not have a route to the peer device.
  B. The local router failed to establish a TCP connection with the peer device.
  C. A firewall is stopping all UDP packets.
  D. The BGP configuration is incomplete.
  B. The local router failed to establish a TCP connection with the peer device.
  D. The BGP configuration is incomplete.

• Question 5:

  Which three statements about nonstop active routing (NSR) are correct? (Choose three.)

  A. NSR uses the graceful Routing Engine switchover infrastructure
  B. NSR and graceful restart work together to reduce downtime during a Routing Engine failure
  C. NSR preservers routing information and protocol sessions on both Routing Engines
  D. NSR requires that both Routing Engines run the same version of software
  E. NSR enables chassisd on both Routing Engines to allow for a smooth transition during a failure
  A. NSR uses the graceful Routing Engine switchover infrastructure
  C. NSR preservers routing information and protocol sessions on both Routing Engines
  D. NSR requires that both Routing Engines run the same version of software

• Question 6:

  Which three elements contribute to the bridge ID when configuring RSTP? (Choose three.)

  A. designated MAC address
  B. priority
  C. extended system ID
  D. root ID
  E. bridge address
  B. priority
  C. extended system ID
  E. bridge address

• Question 7:

  Which statement is true when a VRRP master owns the VIP address?

  A. The VRRP priority will be set to 128.
  B. The VRRP priority will be set to 100.
  C. The VRRP priority will be set to 0.
  D. The VRRP priority will be set to 255.
  D. The VRRP priority will be set to 255.

• Question 8:

  You want to configure an interface on your router to use an IPv6 global IP address.

  Which three methods accomplish this task? (Choose three.)

  A. Use stateless autoconfiguration to assign only the 64 bit interface ID.
  B. Use stateful autoconfiguration to assign only the 64 bit interface ID.
  C. Use stateful autoconfiguration to assign the entire global IPv6 address.
  D. Use a statically assigned global IPv6 address.
  E. Use stateless autoconfiguration to assign the entire global IPv6 address
  A. Use stateless autoconfiguration to assign only the 64 bit interface ID.
  C. Use stateful autoconfiguration to assign the entire global IPv6 address.
  D. Use a statically assigned global IPv6 address.

• Question 9:

  You have multiple Layer 2 interfaces associated with different VLANs configured on an MX Series router. You have been asked to ensure Layer 3 reachability through the MX Series router for the subnets associated with the different VLANs.

  How would you meet this objective?

  A. Use gateway IRB interfaces to forward traffic between VLANs.
  B. Use the BPDU protect feature to direct traffic between VLANs.
  C. Use a Layer 2 routing policy to forward traffic between VLANs.
  D. Use filter-based forwarding to direct traffic between VLANs.
  A. Use gateway IRB interfaces to forward traffic between VLANs.

• Question 10:

  You have built the core of your network using Spanning Tree Protocol. You must ensure that if one of the links between your core switches fails to receive BPDUs it does not mistakenly create a loop. Which feature would you use to ensure BPDUs are always received from neighboring switches to indicate that the remote switch is still alive?

  A. storm control
  B. BPDU control
  C. root protection
  D. loop protection
  C. root protection