Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 511:

  What is a reason for an OSPF router to display a designated router ID of 0.0.0.0?

  A. The MTU is mismatched.
  B. The subnet mask is mismatched.
  C. The interface type is point-to-point.
  D. The interface type is broadcast.
  C. The interface type is point-to-point.

• Question 512:

  What are three circumstances under which a router sends link-state PDUs (LSPs)? (Choose three)

  A. LSPs are sent periodically every 9 seconds
  B. LSPs are sent when there is a network change
  C. LSPs are sent during adjacency formation
  D. LSPs are sent in response to CSNP messages
  E. LSPs are sent in response to PSNP messages
  B. LSPs are sent when there is a network change
  C. LSPs are sent during adjacency formation
  E. LSPs are sent in response to PSNP messages

• Question 513:

  You are asked to configure a GRE tunnel between two remote sites to support the exchange of IPv6 traffic. The two sites are separated by an IPv4 network. Which two configuration elements are required? (Choose two.)

  A. You must enable the GRE interface for IPv6 operations.
  B. You must increase the MTU to no less than 2500.
  C. You must add a static route for the remote IPv6 destination subnet with the remote tunnel endpoint as the next hop at each site.
  D. You must enable the GRE interface for IPv4 operations.
  C. You must add a static route for the remote IPv6 destination subnet with the remote tunnel endpoint as the next hop at each site.
  D. You must enable the GRE interface for IPv4 operations.

• Question 514:

  As frames are processed by a switch, which statement is true about how the switch builds its MAC table?

  A. The source addresses fo the frames are associated with the inbound interface
  B. The source addresses fo the frames are associated with the outbound interface
  C. The destination addresses fo the frames are associated with the inbound interface
  D. The destination addresses fo the frames are associated with the outbound interface
  A. The source addresses fo the frames are associated with the inbound interface

• Question 515:

  You are troubleshooting the status of an RSVP LSP and the output of the "show mpls interface" command is blank. Which statements describes the reason for the blank output?

  A. Authentication was not configured on the local interface
  B. "family mpls" was not configured on the logical interface
  C. No configuration was added to the [edit protocols mpls] hierarchy
  D. No configuration was added to the [edit protocol rsvp] hierarchy
  C. No configuration was added to the [edit protocols mpls] hierarchy

• Question 516:

  Click the Exhibit.

  

  You have configured the IBGP group shown in the exhibit. However, committing your configuration fails. Which parameter should you add to the IBGP group configuration to correct the problem?

  A. Type external
  B. Type internal
  C. Export
  D. As -override
  B. Type internal

• Question 517:

  Click the Exhibit button.

  

  Two bridge domains are configured as shown in the exhibit.

  What must be configured as part of the ge-1/0/3 interface configuration to accept tagged frames of VLANs 100 and 200?

  A. encapsulation vlan-bridge
  B. encapsulation ethernet-bridge
  C. interface-mode trunk
  D. vlan-id-range [100 200]
  C. interface-mode trunk

• Question 518:

  What are tree types of interfaces that can be used in an MX Series device when implementing a virtual switch routing instance? (Choose three.)

  A. Trunk interface
  B. Access interface
  C. Layer 2 logical interface
  D. GRE tunnel interface
  E. Logical tunnel interface
  A. Trunk interface
  B. Access interface
  C. Layer 2 logical interface

• Question 519:

  Click the exhibit.

  

  A customer has two VLANs to extend between Site-1 and Site-2. The customer does not want to route the VLANs or renumber the VLANs.

  Referring to the exhibit, which two VLAN IDs are egressing the MX Series device towards the optical transport network after translation? (Choose two.)

  A. 500
  B. 501
  C. 201
  D. 200
  A. 500
  B. 501

• Question 520:

  What is a requirement for link aggregation?

  A. Member links must be on contiguous ports
  B. Member links must be on the same switch in a Virtual Chassis
  C. The speed of the member links must be the same
  D. LACP must be configured
  C. The speed of the member links must be the same