Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 41:

  Which two statements are correct about a generated route? (Choose two.)

  A. A generated route requires at least two contributing active routes to be active.
  B. A generated route has a route preference of 150.
  C. The primary contributing route is the route with the lowest preference that falls within the aggregate range of prefixes.
  D. A generated route receives the next hop for the primary contributing route.
  C. The primary contributing route is the route with the lowest preference that falls within the aggregate range of prefixes.
  D. A generated route receives the next hop for the primary contributing route.

• Question 42:

  Which statement is true about routing instances on Junos devices?

  A. Routing information cannot be shared between routing instances.
  B. Each routing protocol runs in a separate routing instance.
  C. Junos devices support only one routing instance.
  D. Each routing instance is a unique grouping of routing tables, interfaces, and routing protocol parameters.
  D. Each routing instance is a unique grouping of routing tables, interfaces, and routing protocol parameters.

• Question 43:

  You have been asked to deploy a Layer 2 VPN for a new customer.

  What information will be present in the PE's associated VPN forwarding table? (Choose three.)

  A. the customer site ID
  B. the route distinguisher
  C. the interface encapsulation
  D. the label base
  E. the community name
  A. the customer site ID
  C. the interface encapsulation
  D. the label base

• Question 44:

  You want to verify the frequency and type of SPF calculations on your Junos device. Which command displays this information?

  A. show ospf database | match log
  B. show spf log
  C. show ospf log
  D. show ospf statistics
  C. show ospf log

• Question 45:

  Click the Exhibit button.

  

  Referring to the exhibit, MED is being used in your BGP network. All other BGP configurations use the default settings. Which statement is correct regarding traffic destined to the 151.213.0.0/16 prefix in AS 358?

  A. A traffic black hole will be created at Router A and Router B.
  B. Traffic will load-balance across both the A-to-C and B-to-D paths.
  C. Traffic will prefer the A-to-C path.
  D. Traffic will prefer the B-to-D path.
  C. Traffic will prefer the A-to-C path.

• Question 46:

  You are designing a new MPLS network that contains 1000 nodes. To provide for any-to-any connectivity for your customer base, you have decided to build a full mesh of RSVP LSPs. You are concerned with scalability of the overall network and with the resources used by the devices. Which RSVP feature is used to accomplish your design goals.

  A. authentication
  B. fast reroute
  C. hello interval
  D. refresh reduction
  D. refresh reduction

• Question 47:

  Which two statements are true regarding GRE tunnels? (Choose two.)

  A. GRE can be used to tunnel IP packets only.
  B. A GRE tunnel can be applied only at the physical interface level.
  C. GRE tunnels can be used to send nonroutable packets over a public IP network.
  D. GRE tunnels can be used as backup links.
  C. GRE tunnels can be used to send nonroutable packets over a public IP network.
  D. GRE tunnels can be used as backup links.

• Question 48:

  In the evaluation of an RSTP configuration BPDU, which two values are contained in the Bridge ID value? (Choose two)

  A. root bridge address
  B. priority
  C. originating bridge address
  D. port number
  B. priority
  C. originating bridge address

• Question 49:

  What are two valid protocols used to signal VPLS in a network? (Choose two.)

  A. RSVP
  B. CCC
  C. BGP
  D. LDP
  C. BGP
  D. LDP

• Question 50:

  -- Exhibit -

  

  -- Exhibit -Click the Exhibit button.

  In the exhibit, all switches run STP; however, the link between bridge G and bridge E fails.

  What does root bridge A do after it receives information about this link failure?

  A. Root bridge A sets the acknowledge flag and sends an updated topology BPDU.
  B. Root bridge A sends a topology change notification BPDU.
  C. Root bridge A sets the topology change flag and sends an updated configuration BPDU.
  D. Root bridge A floods an updated BPDU topology database.
  C. Root bridge A sets the topology change flag and sends an updated configuration BPDU.