Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 51:

  Which two statements regarding VRF tables are correct? (Choose two.)

  A. A PE router's VRF table stores routes received from directly connected CE devices.
  B. A PE router's VRF table stores routes received from its IGP from remote PE devices.
  C. A PE router's VRF table stores routes received from MP-BGP from remote PE devices.
  D. A PE router's VRF table stores routes received from all P and PE devices within the same AS.
  A. A PE router's VRF table stores routes received from directly connected CE devices.
  C. A PE router's VRF table stores routes received from MP-BGP from remote PE devices.

• Question 52:

  

  Referring to the network illustrated in the exhibit, how does R1 reach destinations in Area 49.2222?

  A. It uses the routes from Area 49.2222, which it learns from R2
  B. It sees the attached bit from R2 and creates a default route
  C. It must have a default route manually configured
  D. It receives a default route in the IS-IS update from R2
  B. It sees the attached bit from R2 and creates a default route

• Question 53:

  What are two benefits of using MVRP? (Choose two.)

  A. It reduces network administration and overhead
  B. It dynamically creates and prunes VLANs
  C. It provides redundancy for Layer 2 interfaces
  D. It dynamically translates Layer 2 addresses to Layer 3 addresses
  A. It reduces network administration and overhead
  B. It dynamically creates and prunes VLANs

• Question 54:

  Which protocol do multichassis link aggregation group (MC-LAG) devices use to exchange the control information between two MC-LAG network devices?

  A. Virtual Chassis Control Protocol
  B. Multichassis Link Aggregation Protocol
  C. Link Aggregation Control Protocol
  D. Inter-chassis Control Protocol
  D. Inter-chassis Control Protocol

• Question 55:

  An RSVP LSP in your network is operational but you are receiving complaints about network throughput across the LSP. You suspect that the RSVP bandwidth was omitted from the router configuration. Which operational mode command will help you verify your suspicions?

  A. show interfaces terse
  B. show mpls lsp extensive
  C. show rsvp neighbor detail
  D. show rsvp bandwidth
  B. show mpls lsp extensive

• Question 56:

  Where would you configure MVRP in a multiswitch environment?

  A. on all interfaces
  B. on access ports
  C. on trunk ports
  D. within the bridge domain
  C. on trunk ports

• Question 57:

  Click the Exhibit button.

  

  In the exhibit, three IPv6 addresses are listed. Which two statements are true? (Choose two.)

  A. The first address is complete and correct.
  B. The third address is not formatted correctly.
  C. All three addresses are the same.
  D. The second address is incomplete and not correct.
  A. The first address is complete and correct.
  C. All three addresses are the same.

• Question 58:

  Which statement correctly describes a characteristic of IPv6 unicast addressing?

  A. Global addresses are in the range of 2002::/16.
  B. Only one loopback address exists, ::1/128.
  C. Link-local addresses are in the range of FF00::/8.
  D. Link-local addresses are in the range of FE00::/12.
  B. Only one loopback address exists, ::1/128.

• Question 59:

  To which OSPF state does a device transaction once it receives an initial hello packet?

  A. 2Way
  B. Full
  C. ExStart
  D. Exchange
  A. 2Way

• Question 60:

  On an Ethernet segment, OSPF DROther routers form which type of adjacency with each other?

  A. Full
  B. 2Way
  C. ExStart
  D. Exchange
  B. 2Way