Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 381:

  Which statement is true about the operation of a Layer 3 VPN as defined in RFC 4364?

  A. BGP is used for forwarding and MPLS is used for routing
  B. LDP is used for routing and RSVP is used for forwarding
  C. BGP is used for routing and MPLS is used for forwarding
  D. LDP is used for forwarding and MPLS is used for routing
  C. BGP is used for routing and MPLS is used for forwarding

• Question 382:

  Which three statements are true about GRES? (Choose three.)

  A. Kernel information is preserved.
  B. Interface information is preserved.
  C. GRES requires only one RE.
  D. GRES requires redundant REs.
  E. Control plane information is preserved.
  A. Kernel information is preserved.
  B. Interface information is preserved.
  D. GRES requires redundant REs.

• Question 383:

  Which Layer 2 mechanism logically groups network nodes into separate broadcast domains?

  A. IS-IS levels
  B. OSPF areas
  C. VLAN
  D. IP subnets
  C. VLAN

• Question 384:

  Which Junos platform supports provider bridging?

  A. T Series devices
  B. SRX Series devices
  C. MX Series devices
  D. MAG Series devices
  B. SRX Series devices

• Question 385:

  Click the Exhibit.

  

  You are using OSPF as your IGP in your network. You have applied the OSPF configuration shown in the exhibit to router R1. Which statement is true in this scenario?

  A. Router R1 must be configured as a stub area for Area 0.0.0.0.
  B. Router R1 will send a default route to router R2.
  C. Router R2 will not have a route to subnet 172.16.4.0/24.
  D. Router R3 will not have a route to subnet 172.16.3.0/24.
  D. Router R3 will not have a route to subnet 172.16.3.0/24.

• Question 386:

  Click the Exhibit button.

  

  Which two statements are true regarding the output shown in the exhibit? (Choose two.)

  A. The ge-1/0/0 interface will transmit any outgoing frames associated with VLAN 55 as untagged frames.
  B. The ge-1/0/0 interface will associate any untagged frames that are received with VLAN 56.
  C. The ge-1/0/0 interface will associate any untagged frames that are received with VLAN 55.
  D. The ge-1/0/0 interface will transmit any outgoing frames associated with VLAN 56 as untagged frames.
  B. The ge-1/0/0 interface will associate any untagged frames that are received with VLAN 56.
  D. The ge-1/0/0 interface will transmit any outgoing frames associated with VLAN 56 as untagged frames.

• Question 387:

  Which bridging mechanism is used to ensure that only active entries are in the bridge table?

  A. learning
  B. forwarding
  C. flooding
  D. filtering
  E. aging
  E. aging

• Question 388:

  Which three statements are true regarding the show system switchover operational mode command? (Choose three.)

  A. This command can only be issued on the master Routing Engine.
  B. This command displays the status of graceful switchover.
  C. This command can only be issued on the backup Routing Engine.
  D. This command displays the status of the interface and process databases.
  E. This command displays the status of the kernel database.
  B. This command displays the status of graceful switchover.
  C. This command can only be issued on the backup Routing Engine.
  E. This command displays the status of the kernel database.

• Question 389:

  Which two statements about GRE tunnels are true? (Choose two.)

  A. GRE can be used to tunnel non-IP protocols, such as IPX
  B. GRE can provide encrypted communication
  C. GRE adds overhead of 16 bytes per packet
  D. GRE can be used to tunnel IPv6 traffic
  A. GRE can be used to tunnel non-IP protocols, such as IPX
  D. GRE can be used to tunnel IPv6 traffic

• Question 390:

  You are troubleshooting an OSPF adjacency that is stuck in the ExStart state. What would be the correct step to resolve the problem?

  A. Look for a mismatched IP subnet or mask.
  B. Determine whether the neighbor is a DR-Other.
  C. Determine whether the hello and dead intervals are the same on both sides.
  D. Review the MTU settings to ensure that they match.
  D. Review the MTU settings to ensure that they match.