Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 251:

  Which routing table is used to store known IPv6 routes?

  A. inet0
  B. inet.6
  C. inet6.0
  D. inet.2
  C. inet6.0

• Question 252:

  Which two problems occur when increasing numbers of users are added to an Ethernet LAN with no switches present? (Choose two.)

  A. There is a greater chance for collisions to occur
  B. The MAC table sizes increase
  C. Some devices will not see certain traffic
  D. There is unnecessary consumption of network bandwidth
  A. There is a greater chance for collisions to occur
  D. There is unnecessary consumption of network bandwidth

• Question 253:

  Click the Exhibit.

  

  Referring to the exhibit, R-1 and R-2 are connected with a LAG on the ae0 interface. However, the LAG is not operational. Which action will solve this problem?

  A. Change one device to use LACP passive mode.
  B. Change the system ID on one device.
  C. Set the LACP system priority to a non-zero value on one device.
  D. Set the LACP system priority to a non-zero value on both devices.
  B. Change the system ID on one device.

• Question 254:

  How many equal-cost paths can be assigned to a single route in the Junos OS?

  A. 4
  B. 16
  C. 32
  D. 64
  B. 16

• Question 255:

  Which two fields of a hello packet must match on both routers when forming an OSPF adjacency? (Choose two.)

  A. Hello interval
  B. Designated route
  C. Router priority
  D. Network mask
  B. Designated route
  D. Network mask

• Question 256:

  Click the Exhibit.

  

  The router with the configuration shown in the exhibit has two interfaces, both of which are operational and can pass traffic. These interfaces are connected to two different routers, both of which are configured for OSPF area 0.0.0.1. The router has received LSAs and can now send traffic into the backbone area.

  Which two statements are correct? (Choose two.)

  A. The router is an ASBR.
  B. The router has only a single OSPF adjacency.
  C. The router is an ABR.
  D. The router has two OSPF adjacencies.
  B. The router has only a single OSPF adjacency.
  C. The router is an ABR.

• Question 257:

  You are asked to configure a new external BGP connection to a peer's loopback interface. You verify that the peer's loopback interface is reachable, but the BGP connection remains in Idle state. Which BGP parameter is required to establish the BGP connection?

  A. multipath
  B. multihop
  C. as-override
  D. advertise-inactive
  B. multihop

• Question 258:

  You are establishing RSVP LSPs through your MPLS-enabled network. You are asked to ensure that the LSPs will support end-to-end class-of-service handling. Which statement is correct in this scenario?

  A. Configure ultimate-hop-popping on the egress device.
  B. Configure implicit-null on all MPLS-enabled devices.
  C. Configure explicit-null on all MPLS-enabled devices.
  D. Configure entropy-label on the egress device.
  A. Configure ultimate-hop-popping on the egress device.

• Question 259:

  

  Click the Exhibit button.

  You work for the regional Internet service provider shown in the exhibit. You have a partial BGP table and are receiving a 10.100/16 route from your upstream ISP. You have been asked to configure a default route that can be sent to your downstream customer. This route should forward customer traffic toward your upstream Tier 1 ISP as long as the 10.100/16 route is present.

  What would accomplish this goal?

  A. Create and announce an aggregate default route.
  B. Create and announce a static default route with a next-hop of discard.
  C. Create and announce a static default route with a next-hop of reject.
  D. Create and announce a generated default route.
  D. Create and announce a generated default route.

• Question 260:

  Which two statements correctly describe IS-IS adjacencies? (Choose two.)

  A. Level 1 adjacencies can form in the same (intra) area only.
  B. Level 2 adjacencies are formed between (inter) areas only.
  C. Level 2 adjacencies can be established either interarea or intra-area.
  D. Level 2 adjacencies can form within the same (intra) area only.
  A. Level 1 adjacencies can form in the same (intra) area only.
  C. Level 2 adjacencies can be established either interarea or intra-area.