Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 241:

  Which two configuration elements are defined under an MSTP instance? (Choose two)

  A. revision-level
  B. bridge-priority
  C. mstp-level
  D. vlan
  B. bridge-priority
  D. vlan

• Question 242:

  On an MX Series device with dual Routing Engines, which two conditions cause a unified ISSU to fail? (Choose two.)

  A. Graceful restart is disabled.
  B. BFD is enabled.
  C. GRES is disabled.
  D. NSR is disabled.
  C. GRES is disabled.
  D. NSR is disabled.

• Question 243:

  Because of recent network failures, additional circuits have been purchased. In addition, Fast reroute has been configured on critical MPLS LSPs. When the next failure occurs, which two time intervals will affect fast reroute? (Choose two.)

  A. The amount of time required to reroute the traffic onto the detour
  B. The amount of time to detect a link or node failure
  C. The amount of time required to recalculate the best detour
  D. The amount of time it takes to ping the gateway on the detour link
  A. The amount of time required to reroute the traffic onto the detour
  B. The amount of time to detect a link or node failure

• Question 244:

  You have just configured IPv6 in your network. A packet arrives on your router that exceeds the MTU size. How will an IPv6 router respond?

  A. The fragment offset is referenced and the packet is fragmented.
  B. The packet is kept intact and not fragmented.
  C. The packet is dropped.
  D. The packet is fragmented based on extension headers.
  C. The packet is dropped.

• Question 245:

  Click the Exhibit button.

  

  An ISO NET has been configured on R2's lo0.0 interface and ge-0/0/2.0 has been configured to run IS-IS. However, IS-IS adjacency on ge-0/0/2.0 is not coming up. Referring to the exhibit, what is required to enable IS-IS?

  A. Configure the family iso parameter under the ge-0/0/2.0 interface.
  B. Disable Level 2 for interface ge-0/0/2.0
  C. Add the lo0.0 interface under the [edit protocols isis] hierarchy.
  D. Configure the interface priority for ge-0/0/2.0.
  A. Configure the family iso parameter under the ge-0/0/2.0 interface.

• Question 246:

  Which criterion is evaluated first when selecting a BGP route?

  A. MED
  B. origin
  C. local preference
  D. AS-path
  C. local preference

• Question 247:

  In your network, you have two LDP routers connected across four physical interfaces. You have also enabled LDP to operate on all four of those interfaces. What is the resulting outcome of your configuration between those two routers?

  A. One session is built across one neighbor relationship
  B. One session is built across four neighbor relationships
  C. Four sessions are built across one neighbor relationship
  D. Four sessions are built across four neighbor relationships
  B. One session is built across four neighbor relationships

• Question 248:

  You have an established Layer 3 VPN where you are using static routing between your PE and CE devices. You must advertise their directly connected subnet to remote PE devices. Which two methods must you use? (Choose two.)

  A. Use a site identifier.
  B. Use the VRF table label.
  C. Use a VRF export policy.
  D. Use a route distinguisher.
  B. Use the VRF table label.
  C. Use a VRF export policy.

• Question 249:

  Click the Exhibit button

  policy-options {

  policy-statement load-balance {

  then {

  load-balance per-packet;

  }

  }

  }

  When the configuration shown in the exhibit is applied, which routes in the forwarding table will begin load-balancing packet flows?

  A. all routes in the forwarding table
  B. all OSPF routes in the forwarding table
  C. all BGP routes in the forwarding table
  D. all RFC 1918 routes in the forwarding table
  A. all routes in the forwarding table

• Question 250:

  Which two routing protocols make use a designated router, or pseudo node, to represent a broadcast network? (Choose two.)

  A. BGP
  B. OSPF
  C. MPLS
  D. IS-IS
  B. OSPF
  D. IS-IS