Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 191:

  Using industry best practices, which two BGP attributes would you modify to influence how traffic enters your network? (Choose two)

  A. AS Path
  B. Local Preference
  C. Next Hop
  D. MED
  A. AS Path
  D. MED

• Question 192:

  In a Junos device functioning as an MPLS transit router, which routing table is used when performing a forwarding lookup for an incoming packet?

  A. mpls.3
  B. inet.0
  C. inet.3
  D. mpls.0
  C. inet.3

• Question 193:

  What is the purpose of a route target community in a Layer 3 VPN?

  A. The community value is used to identify routes that should be imported by remote PEs.
  B. The community value is used to determine valid remote devices when signaling a Layer 3 VPN.
  C. The community value is used to identify the source of incoming routes.
  D. The community value is used to determine transit devices when signaling a Layer 3 VPN.
  A. The community value is used to identify routes that should be imported by remote PEs.

• Question 194:

  After configuring OSPF between two routers you check for an adjacency. You see that the adjacencies are not coming up on an Ethernet segment. What are two reasons that would cause this situation? (Choose two)

  A. You have a mismatched IP subnet/mask
  B. Your hello timer intervals are mismatched
  C. You are not using the same Junos version on each side
  D. You priority values are mismatched
  A. You have a mismatched IP subnet/mask
  B. Your hello timer intervals are mismatched

• Question 195:

  Your network consists of multiple remote locations using both IPv4 and IPv6. You have an IPv4-based Internet connection at each site provided by different, local service providers. You are asked to ensure that the remote IPv6 networks are able to communicate.

  What should you do?

  A. Create GRE tunnels between the remote locations to connect the IPv6 networks.
  B. Create IPsec tunnels between the remote locations to connect the IPv6 networks.
  C. Create IP-IP tunnels between the remote locations to connect the IPv6 networks.
  D. Create MPLS tunnels between the remote locations to connect the IPv6 networks.
  C. Create IP-IP tunnels between the remote locations to connect the IPv6 networks.

• Question 196:

  You have configured an RSVP LSP in your network and have assigned it one primary and two secondary paths. Which command is used to validate that the LSP is using the primary path?

  A. show rsvp interface
  B. show rsvp version
  C. show rsvp neighbor detail
  D. show rsvp session detail
  D. show rsvp session detail

• Question 197:

  Click the Exhibit button.

  

  Referring to the exhibit, which two statements are correct about R2? (Choose two.)

  A. If R2 remains in the ExStart state, then you should verify the MTU setting on R2 and R3.
  B. R2 LSDB is synchronized with R1.
  C. If R2 remains in the ExStart state, then you should verify Physical Layer and Data Link Layer connectivity on R2 and R3.
  D. R2 LSDB is not synchronized with R1.
  A. If R2 remains in the ExStart state, then you should verify the MTU setting on R2 and R3.
  B. R2 LSDB is synchronized with R1.

• Question 198:

  Which two support tunneling for non-IP protocols on Junos devices? (Choose two.)

  A. ATM AAL2
  B. GRE
  C. IP-IP
  D. ATM AAL1
  B. GRE
  C. IP-IP

• Question 199:

  Your OSPF network design uses stub areas extensively due to 5000 external routes within the backbone and resource constraints in the nonbackbone areas. You now have a device in Area 2 that must perform as an ASBR. Which OSPF area types should you use for Area 2?

  A. stub
  B. non-backbone area
  C. not-so-stubby-area
  D. totally stubby area
  C. not-so-stubby-area

• Question 200:

  You have three aggregate routes all with the same route preference. What is the second parameter used to determine the active route?

  A. lowest metric value
  B. secondary route preference
  C. highest metric value
  D. lowest community value
  B. secondary route preference