Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 181:

  By default, which BGP attribute is only compared when two route advertisements are received from the same neighboring AS?

  A. MED
  B. AS-Path
  C. Communities
  D. Next Hop
  A. MED

• Question 182:

  You are attempting to influence return traffic into your autonomous system by preferring one router as an entry point. Which two BGP attributes will affect this behavior? (Choose two.)

  A. originator ID
  B. local preference
  C. AS path
  D. MED
  C. AS path
  D. MED

• Question 183:

  You must configure an OSPF area that does not accept type 3 link-state advertisements (LSAs) from area 0 (other than the default route) You have configured your area to be stub, but you still see type 3 LSAs. What will account for this behavior?

  A. You should have configured your area as totally stubby
  B. You should have used a not-so-stubby-area
  C. You are experiencing a routing loop
  D. You have exported routes into OSPF
  A. You should have configured your area as totally stubby

• Question 184:

  Which two statements are correct regarding BGP-signaled Layer 2 VPNs? (Choose two.)

  A. You must enable the Layer 2 VPN signaling NLRI.
  B. You must configure the virtual circuit identifier.
  C. You must specify the neighbor using the tunnel end-point IP address.
  D. You must define a unique site-identifier value.
  A. You must enable the Layer 2 VPN signaling NLRI.
  D. You must define a unique site-identifier value.

• Question 185:

  Which two Layer 2 protocols are supported on MX Series devices? (Choose two.)

  A. BGP
  B. RIP
  C. RSTP
  D. MSTP
  C. RSTP
  D. MSTP

• Question 186:

  Which forwarding table designation is used to indicate that load balancing is working correctly?

  A. ucst
  B. msct
  C. ulst
  D. mlst
  C. ulst

• Question 187:

  -- Exhibit -

  protocols {

  isis {

  interface lo0.0;

  interface ge-0/0/0.100;

  }

  }

  -- Exhibit -

  Click the Exhibit button.

  Referring to the exhibit, what will be the IS-IS levels enabled on the interface ge-0/0/0.100?

  A. Level 1 only
  B. Level 2 only
  C. Level 1 and Level 2
  D. Level 1, Level 2, and Level 3
  C. Level 1 and Level 2

• Question 188:

  -- Exhibit -protocols {

  isis {

  level 1 disable;

  interface ge-1/0/0.0 {

  level 2 disable;

  }

  interface ge-1/1/0.0;

  interface lo0.0;

  }

  }

  -- Exhibit -

  Click the Exhibit button.

  Referring to the exhibit, what is the resulting behavior on interface ge-1/0/0?

  A. Level 1 is enabled.
  B. Level 1 is disabled.
  C. Level 2 is enabled.
  D. Level 1 and Level 2 are disabled.
  A. Level 1 is enabled.

• Question 189:

  What are two uses of the AS-path attribute? (Choose two.)

  A. It is used in BGP route selection.
  B. It is used to ensure that a packet traverses the least number of routers.
  C. It is used by IGPs to avoid loops within an autonomous system.
  D. It is used to avoid routing loops between autonomous systems.
  A. It is used in BGP route selection.
  D. It is used to avoid routing loops between autonomous systems.

• Question 190:

  Click the Exhibit.

  

  Referring to the exhibit, what is the correct OSPF interface state for the ge-0/0/1 interface?

  A. BDR
  B. Down
  C. DR
  D. DR other
  C. DR