Huawei H12-211 Online Practice Questions and Exam Preparation

Huawei H12-211 Online Questions & Answers

• Question 371:

  Which of the following statements about a designated port working in RIPv2 multicast mode are true? (Choose three)

  A. The port receives only RIPv2 multicast packets.
  B. The port does not receive RIPv1 broadcast packets.
  C. The port does not receive RIPv2 broadcast packets.
  D. The port receives only RIPv1 multicast packets.
  A. The port receives only RIPv2 multicast packets.
  B. The port does not receive RIPv1 broadcast packets.
  C. The port does not receive RIPv2 broadcast packets.

• Question 372:

  To provide the information about the IP addresses that a user packet traverses along the path to the destination, which of the following does Tracert record in each expired ICMP TTL packet?

  A. Destination port
  B. Source port
  C. Destination address
  D. Source address
  D. Source address

• Question 373:

  Which of the following port status may exist on an STP-enabled switch?

  A. Forwarding
  B. Listening
  C. Discarding
  D. Disabled
  A. Forwarding
  B. Listening

• Question 374:

  Which of the following descriptions regarding IPv6 addresses are correct? (Choose two)

  A. IPv6 addresses are 64 bits in length.
  B. IPv6 addresses are 128 bits in length.
  C. IPv6 extension headers are processed in order.
  D. IPv6 extension headers are processed randomly.
  B. IPv6 addresses are 128 bits in length.
  C. IPv6 extension headers are processed in order.

• Question 375:

  Which of the following statements are true about the default route?

  A. In a routing table, the route to 0.0.0.0 (with the mask being 0.0.0.0) is the default route.
  B. If the destination address of a packet does not match any entry in the routing table, the packet is forwarded through the default route.
  C. The default route can only be manually configured by the administrator.
  D. The routing table of any router must contain the default route.
  A. In a routing table, the route to 0.0.0.0 (with the mask being 0.0.0.0) is the default route.
  B. If the destination address of a packet does not match any entry in the routing table, the packet is forwarded through the default route.

• Question 376:

  The company network engineer has an AR2200 that cannot be started normally. How can the administrator want to update its VRP?

  A. The administrator needs to use the console cable to connect to the router and host, and then enter the BootROM interface to complete the upgrade.
  B. The administrator needs to configure the AR2200 as an FTP client and use FTP to transfer the new
  C. The administrator needs to configure the AR2200 to obtain an IP address through DHCP and then obtain the VRP system file through TFTP.
  D. The administrator needs to use telnet on the local host to remotely update the VRP system files of the device.
  B. The administrator needs to configure the AR2200 as an FTP client and use FTP to transfer the new

• Question 377:

  Regarding the correspondence between the access control list number and the type, the following description is correct (). Huawei question bank battle report group: 434299778

  A. The basic access control list number range is 1000-2999
  B. Advanced access control list number range is 3000-9000
  C. The basic access control list number range is 4000-4999
  D. The basic access control list number range is 1000-2000
  C. The basic access control list number range is 4000-4999

• Question 378:

  Which of the following storage media are commonly used by Huawei routers? (multiple choice)

  A. SDRAM
  B. NVRAM
  C. Flash
  D. Hard Disk
  E. SD Card
  A. SDRAM
  B. NVRAM
  C. Flash
  E. SD Card

• Question 379:

  A client failed to transfer a file to the FTP server, but found the IP connectivity was without problem. The client assumed that the problem was with the port configuration. The blocking of which ports would likely cause this problem? (Choose two)

  A. 21
  B. 80
  C. 20
  D. 50649
  A. 21
  C. 20

• Question 380:

  In port aggregation, "multiple" ports are aggregated to form a port aggregation group so that all the member ports in the group share the outgoing/incoming load. At which layer is port aggregation implemented?

  A. Physical Layer
  B. Data Link Layer
  C. Network Layer
  D. Transport Layer
  B. Data Link Layer