Riverbed 830-01 Online Practice Questions and Exam Preparation

Riverbed 830-01 Online Questions & Answers

• Question 361:

  What information is available in the System Snapshot files on the Steelhead Mobile Controller?

  A. A copy of all memory
  B. A copy of hardware registers
  C. Status indicators
  D. System configs and tcpdumps
  E. A, B, and C
  E. A, B, and C

• Question 362:

  What ports are required for proper operation of the Steelhead Mobile client?

  A. 7800 outbound, 7801 inbound, 7870 outbound
  B. 7800 inbound, 7870 inbound, 7870 outbound
  C. 7800 inbound, 7801 outbound, 7870 outbound
  D. None of the above
  A. 7800 outbound, 7801 inbound, 7870 outbound

• Question 363:

  To configure a Steelhead appliance for logical in-path mode, the following must be enabled in the General Service Settings page:

  A. Reset Existing Client Connections on Start Up
  B. Enable L4/PBR/WCCP Support on Interface wan0_0
  C. Enable Optimizations on Interface inpath0_0
  D. B and C
  E. A, B, and C
  D. B and C

• Question 364:

  -- Exhibit

  

  -- Exhibit -Refer to the exhibit. According to the log information, what does that message represent? (Select 2)

  A. This Steelhead appliance is closing its out-of-band Splice with the peer Steelhead appliance 172.16.10.101.
  B. This Steelhead appliance is closing its out-of-band Splice with the peer Steelhead appliance 172.16.11.101.
  C. The local Steelhead appliance is 172.16.11.101.
  D. The local Steelhead appliance is 172.16.12.101.
  B. This Steelhead appliance is closing its out-of-band Splice with the peer Steelhead appliance 172.16.11.101.
  D. The local Steelhead appliance is 172.16.12.101.

• Question 365:

  -- Exhibit

  

  -- Exhibit -Refer to the exhibit. A Steelhead administrator has decided to implement two Interceptor appliances and one Steelhead appliance on his data center. After configuring the Interceptor appliances, and the Steelhead appliance, he decided to check if the connections are being forwarded appropriately. Which Interceptor diagnostic tool did the administrator use?

  A. Connection diagnostic.
  B. Connection tracer.
  C. Optimization tracing.
  D. Connection tracing.
  E. Debug validate deployment.
  D. Connection tracing.

• Question 366:

  When deploying policy-based routing for multiple Steelhead appliances in a cluster, the router should be configured to: (Select 2)

  A. Set IP next-hop address to the virtual IP address of the Steelhead appliance cluster
  B. Set IP next-hop addresses for each Steelhead appliance
  C. Check the state level information on each Steelhead appliance via SLA or CDP
  D. Auto-detect the Steelhead appliance clustering protocol
  E. Check the state level information on the virtual IP address of the Steelhead appliance cluster
  B. Set IP next-hop addresses for each Steelhead appliance
  C. Check the state level information on each Steelhead appliance via SLA or CDP

• Question 367:

  You have an existing Steelhead appliance deployment which is achieving excellent optimization at five sites. You have deployed a Steelhead appliance physically in-path at a new small branch office and all of your applications have become slower for this new branch office only. What is the likely cause?

  A. Incorrect in-path rules at the data-center
  B. Incorrect in-path rules at the new branch office
  C. Duplex mismatch between the new branch Steelhead and a connected device
  D. Duplex mismatch between the data-center Steelhead and a connected device
  E. Incorrect peering rules at the data-center
  F. Incorrect peering rules at the new branch office
  C. Duplex mismatch between the new branch Steelhead and a connected device

• Question 368:

  You wish to utilize a SteelHead to fill a high bandwidth, high latency WAN link without data reduction. The link is 622mbps and 500ms latency. What steps should you take to fill the pipe?

  A. Enable HSTCP, configure the WAN buffers and enable SDR/LZ.
  B. Enable HSTCP, configure the WAN buffers and disable SDR/LZ.
  C. Max-TCP and HS-TCP are only for optimized flows, so data reduction cannot be disabled but will fill the pipe anyway.
  D. Enable MXTCP, configure the WAN buffers and disable SDR/LZ.
  E. Enable MXTCP, configure the WAN buffers and enable SDR/LZ.
  B. Enable HSTCP, configure the WAN buffers and disable SDR/LZ.

• Question 369:

  When would Simplified Routing Destination Only be used? (Select 2)

  A. HSRP (Hot Standby Routing Protocol)
  B. VLAN bridging
  C. Multiple firewalls
  D. Bridged network
  E. There is no setting for Destination Only
  A. HSRP (Hot Standby Routing Protocol)
  D. Bridged network

• Question 370:

  What is the default Connection Forwarding keep alive interval?

  A. 1 second
  B. 3 seconds
  C. 5 seconds
  D. 10 seconds
  E. 15 seconds
  A. 1 second