Cisco Cisco Certifications 352-001 Questions & Answers

• Question 641:

  You are designing a network for a branch office. In order to improve convergence time, you are required to use the BFD feature. Which four routing protocols can you use to facilitate this? (Choose four.)

  A. EIGRP

  B. IS-IS

  C. BGP

  D. static

  E. RIP

  Correct Answer: ABCD

• Question 642:

  Refer to the exhibit.

  

  A service provider would like to use Ethernet OAM to detect end-to-end connectivity failures between SP-SW1 and SP-SW2. In which two of these ways can you design this solution? (Choose two.)

  A. Enable Y.1731 Connectivity Fault Management on the SP switches.

  B. E-LMI PDUs must be forwarded over VPLS.

  C. Cisco Discovery Protocol PDUs must be forwarded over the VPLS.

  D. Use upward maintenance endpoints on the SP switches.

  E. Enable IEEE 802.1ag Connectivity Fault Management on the SP switches.

  Correct Answer: DE

• Question 643:

  What are two reasons for instrumenting your network and network devices to collect performance data? (Choose two.)

  A. to determine the impact of jitter and latency on application performance

  B. to enable capacity planning decisions

  C. to route traffic around constrained choke points in the network

  D. to determine the locations at which QoS needs to be implemented

  Correct Answer: BD

• Question 644:

  Refer to the exhibit.

  

  On R2 there is a summary route for 192.168.1.0/24 with a next hop of R4. Which change will cause R2 to prefer a path through R1 to reach 192.168.1.0/24?

  A. convert Area 1 to a stub area and decrease the cost between R1 and R3 to 1

  B. create a virtual link between R1 and R2

  C. create a virtual link between R1 and R2 and decrease the cost between R1 and R3 to 1

  D. change the link between R1 and R2 to Area 0

  Correct Answer: C

• Question 645:

  A company requests that you consult with them regarding the design of their production, development, and test environments. They indicate that the environments must communicate effectively, but they must be kept separate due to the inherent failures on the development network. What will be configured on the links between the networks to support their design requirements?

  A. IBGP

  B. EBGP

  C. OSPF

  D. static routes

  Correct Answer: B

• Question 646:

  Which IPv4 addressing and routing scheme can increase the availability of a network service during a DoS attack?

  A. unicast

  B. broadcast

  C. anycast

  D. multicast

  Correct Answer: C

• Question 647:

  ACME Corporation is deploying a new HR application that requires the network infrastructure to monitor and react to certain conditions in the network. Which feature should be used to meet this design requirement?

  A. Cisco IOS Embedded Event Manager

  B. IP SLA

  C. reflexive ACLs

  D. route maps

  E. SOAP

  F. exit status

  Correct Answer: A

• Question 648:

  A senior network designer suggests that you should improve network convergence times by reducing BGP timers between your CE router and the PE router of the service provider. Which three factors should you to consider when you adjust the timer values? (Choose three.)

  A. access bandwidth

  B. service provider agreement to support tuned timers

  C. number of routes on the CE router

  D. number of VRFs on the PE router

  E. service provider scheduling of changes to the PE

  Correct Answer: ABC

• Question 649:

  Your company plans to implement an Internet gateway router that is performing NAT. This same gateway will be terminating various IPsec tunnels to other remote sites. Which address type is appropriate for the ACL that will govern the sources of traffic entering the tunnel in the inside interface?

  A. inside local

  B. inside global

  C. outside local

  D. outside global

  Correct Answer: B

• Question 650:

  Refer to the exhibit.

  

  All routers in this network are configured to run OSPF on all interfaces. If you examine the OSPF database on R4, in which LSA will you find 10.1.5.0/24?

  A. 10.1.5.0/24 is in a network (type 2) LSA originated by R3.

  B. 10.1.5.0/24 is in a summary (type 3) LSA originated by R3.

  C. 10.1.5.0/24 is not in any LSA in the OSPF database at R4, because R4 and R3 are in different areas.

  D. 10.1.5.0/24 is in a router (type 1) LSA generated by R3.

  Correct Answer: B