Cisco 352-001 Online Practice Questions and Exam Preparation

Cisco 352-001 Online Questions & Answers

• Question 631:

  You are working on a network design plan for a company with approximately 2000 sites. The sites will be connected using the public Internet. You plan to use private IP addressing in the network design, which will be routed without NAT through an encrypted WAN network. Some sites will be connected to the Internet with dynamic public IP addresses, and these addresses may change occasionally. Which VPN solution will support these design requirements?

  A. GET VPN must be used, because DMVPN does not scale to 2000 sites.
  B. DMVPN must be used, because GET VPN does not scale to 2000 sites.
  C. GET VPN must be used, because private IP addresses cannot be transferred with DMVPN through the public Internet.
  D. DMVPN must be used, because private IP addresses cannot be transferred with GET VPN through the public Internet.
  E. GET VPN must be used, because DMVPN does not support dynamic IP addresses for some sites.
  F. DMVPN must be used, because GET VPN does not support dynamic IP addresses for some sites.
  D. DMVPN must be used, because private IP addresses cannot be transferred with GET VPN through the public Internet.

• Question 632:

  Which three factors effects the convergence times in an OSPF network? (Choose three.)

  A. OSPF SPF throttling timers
  B. OSPF pacing timers
  C. OSPF LSA throttling
  D. LSA refresh interval
  E. DR/BDR election
  F. OSPF LSA lifetime
  A. OSPF SPF throttling timers
  B. OSPF pacing timers
  C. OSPF LSA throttling

• Question 633:

  As part of a new network design, you are helping the Network Management Team to develop a proactive report to identify places in the network where problems may happen. The network management tool can poll the network devices only via SNMP GET operations. Which two threshold-crossing metrics should you include in this report? (Choose two.)

  A. packet loss
  B. CPU utilization
  C. heat dissipation
  D. IP reachability
  E. energy consumption
  F. link bandwidth utilization
  B. CPU utilization
  F. link bandwidth utilization

• Question 634:

  Which design concern should be accounted for in all Layer 3 virtualization technologies?

  A. Layer 3 redundancy
  B. packet sizing
  C. application usage
  D. Layer 3 stability
  B. packet sizing

• Question 635:

  Refer to the exhibit.

  

  In this BGP design, what is the next hop for 10.1.1.0/24 on R8 and R7?

  A. The next hop for 10.1.1.0/24 on R7 is R8 and the next hop for R8 is R7.
  B. The next hop for 10.1.1.0/24 on R7 is R5 and the next hop for R8 is R6.
  C. The next hop for 10.1.1.0/24 on R7 is R6 and the next hop for R8 is R5.
  D. The next hop for 10.1.1.0/24 on R7 is R3 and the next hop for R8 is R4.
  A. The next hop for 10.1.1.0/24 on R7 is R8 and the next hop for R8 is R7.

• Question 636:

  What is the primary requirement for deploying OSPF graceful restart on a router?

  A. Aggressive routing protocol hellos and keepalives must be running on the router.
  B. The adjacent router must support graceful restart helper mode.
  C. Some form of fast Layer 2 down detection must be enabled on the router.
  D. The adjacent routers must be enabled to forward traffic during the failure.
  B. The adjacent router must support graceful restart helper mode.

• Question 637:

  In an OSPF network with 20 routers connected together with Ethernet cabling , which topology typically takes the longest to converge?

  A. Full mesh
  B. Ring
  C. Squared
  D. Triangulated
  E. Partial mesh
  B. Ring

• Question 638:

  If a network design must support rapid convergence on half-duplex interfaces, which IEEE 802.1w capability should be used?

  A. root guard
  B. proposal-agreement handshake
  C. loop guard
  D. UplinkFast
  B. proposal-agreement handshake

• Question 639:

  Among the design criteria for a network is the requirement that bandwidth capacity be managed proactively.

  Which two techniques would most effectively support the proactive management of network bandwidth capacity? (Choose two.)

  A. analyze network bandwidth utilization to establish a baseline
  B. implement QoS to increase available bandwidth and overall throughput
  C. implement utilization measurement and tracking measures in the network
  D. configure SNMP MIB collectors to trigger at utilization thresholds
  A. analyze network bandwidth utilization to establish a baseline
  C. implement utilization measurement and tracking measures in the network

• Question 640:

  When you design a network that uses IPsec, where can you reduce MTU to avoid network fragmentation?

  A. on both ends of the TCP connection
  B. on the side closest to the client
  C. on the side closest to the server
  D. in the WAN
  A. on both ends of the TCP connection