Cisco 350-601 Online Practice Questions and Exam Preparation

Cisco 350-601 Online Questions & Answers

• Question 81:

  An engineer must build a lab replica of a Cisco UCS production environment. The file must be imported into a new Cisco UCS cluster using a Cisco UCS manager GUI. The file must be in XML format and be exported from Cisco UCS Manager using encrypted method.

  Which two configuration parameters should be selected to meet these requirements?. (Choose two.)

  A. Type: Logical configuration
  B. Protocol: SCP
  C. Type: Full state
  D. Protocol: TFTP
  E. Type: All configuration
  B. Protocol: SCP
  E. Type: All configuration

• Question 82:

  Refer to the exhibit.

  

  Which result of running the command is true?

  A. The PIM database is deleted.
  B. Multicast traffic forwarding is suspended.
  C. PIM join messages are suspended.
  D. MRIB is flushed
  A. The PIM database is deleted.

  ---

  Explanation

  When you restart PIM, the following tasks are performed: The PIM database is deleted. The MRIB and MFIB are unaffected and forwarding of traffic continues. The multicast route ownership is verified through the MRIB. Periodic PIM join and prune messages from neighbors are used to repopulate the database.

  https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus9000/sw/6-x/multicast/configuration/guide/b_Cisco_Nexus_9000_Series_NX-OS_Multicast_Routing_Configuration_Guide/b_Cisco_Nexus_9000_Series_NX-OS_Multicast_Routing_Configuration_Guide_chapter_011.html

• Question 83:

  DRAG DROP

  An engineer must configure Cisco UCS Manager to accept only HTTPS connections that use TLS 1 2 The cipher security level must be high and the length of the keyring key value must be 2048 bits.

  Drag and drop the code snippets from the right onto the blanks in the code on the left to accomplish these goals. Not all commands are used.

  Select and Place:

  

  

• Question 84:

  What are two requirements when planning a Cisco HyperFlex All Flash standard cluster installation using three HX240c M5 servers? (Choose Two)

  A. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames do not have to be enabled on the upstream switches.
  B. The hypervisors must be installed to Cisco FlexFlash SD cards.
  C. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames must also be enabled on the upstream switches.
  D. The cluster deployment type must support a mix of HDD and SSD.
  E. The servers must be discovered, unassociated, and connected to each fabric interconnect.
  C. If the Jumbo MTU option in the HyperFlex installer is enabled, then jumbo frames must also be enabled on the upstream switches.
  E. The servers must be discovered, unassociated, and connected to each fabric interconnect.

  ---

  Explanation

  https://www.cisco.com/c/en/us/td/docs/hyperconverged_systems/HyperFlex_HX_DataPlatformSoftware/AdminGuide/3_5/b_HyperFlexSystems_AdministrationGuide_3_5/b_HyperFlexSystems_AdministrationGuide_3_5_chapter_01111.html

• Question 85:

  An engineer must perform a software upgrade on a production Cisco Nexus 7000 Series Switch. Before the upgrade activity, the requirement is for all ports to be shut down and routing protocols to terminate gracefully.

  Which feature must be used to meet these requirements?

  A. Switch Profile
  B. Service Profile Template
  C. Maintenance Mode Profile
  D. Configuration Profile
  C. Maintenance Mode Profile

• Question 86:

  Refer to the exhibit.

  

  An engineer monitors ingress traffic from Host-A and all traffic for VLAN 20 from Host-B. Which configuration must be implemented to monitor and export traffic to Network Analyzer?

  A. SW-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 tx SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination ip 10.10.10.1 SW-1(config-monitor)# no shut
  B. SW-1(config)# monitor session 5 type erspan-source SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source vlan 20 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# erspan-id 111 SW-1(config-erspan-src)# no shut
  C. SW-1(config)# monitor session 5 SW-1(config-monitor)# source interface ethernet 1/2 rx SW-1(config-monitor)# source interface ethernet 1/1 both SW-1(config-monitor)# source vlan 20 both SW-1(config-monitor)# destination interface ethernet 2/1 SW-1(conflg-monitor)# no shut
  D. SW-1(config)# monitor session 5 type erspan SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source interface ethernet 1/1 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# mtu 1000 SW-1(config-erspan-src)# no shut
  B. SW-1(config)# monitor session 5 type erspan-source SW-1(config-erspan-src)# source interface ethernet 1/2 rx SW-1(config-erspan-src)# source vlan 20 both SW-1(config-erspan-src)# destination ip 10.10.10.1 SW-1(config-erspan-src)# erspan-id 111 SW-1(config-erspan-src)# no shut

• Question 87:

  An engineer requires a solution to automate the configuration and deployment of remote network devices for a customer. The engineer must keep these considerations in mind:

  1. The customer's environment is based on industry-accepted standards and requires a solution that meets these standards.

  2. The security requirements mandate the use of a secure transport mechanism between the automation software and target devices such as SSH or TLS.

  3. The solution must be based on a human-readable and easy to parse format such as XML or JSON.

  Which solution must be used to meet these requirements?

  A. SNMP
  B. REST API
  C. Ansible
  D. NETCONF
  D. NETCONF

  ---

  Explanation

  https://www.cisco.com/c/en/us/products/collateral/ios-nx-os-software/ios-xe/nb-06-cisco-ios-xe-faq-en.html

• Question 88:

  An engineer needs to install a new package on a Cisco Nexus 9000 Series Switch.

  What is the impact of running the install commit <filename> command on the switch?

  A. The switch is restarted after the upgrade is complete.
  B. The package is used after the switch is restarted
  C. The package is used in the running configuration.
  D. The previous package that was in use is deleted from bootflash.
  B. The package is used after the switch is restarted

• Question 89:

  A new user with access privileges in the Finance department moves to a new Admin department. The user must have access privileges to the Admin department data and applications inside the Cisco UCS Manager.

  Which set of changes must be implemented in Cisco UCS Central for the user to acquire the privileges?

  A. Disable the Finance user account and add the authentication service for the Admin privileges.
  B. Create a new locale Admin and add the Admin department to the Admin locale.
  C. Create an Admin user account and remove the authentication service for the Finance privileges.
  D. Delete the old locale Finance and remove the Finance department from the Finance locale.
  B. Create a new locale Admin and add the Admin department to the Admin locale.

• Question 90:

  An engineer upgrades the bash on the Cisco Nexus 9000 Series Switch.

  

  Which command must be sed to complete the task?

  A. rpm -qa
  B. rpm -Uhv
  C. upgrade -U
  D. update -vh
  B. rpm -Uhv