Cisco CCNP 350-601 Questions & Answers

• Question 51:

  DRAG DROP

  An engineer must configure a control plane policy on a Cisco Nexus 9000 Series Switch that is located at IP 192.168 20.1 that moots those requirements:

  1.

  Only HTTP. RDP. and ICMP traffic is permitted from subnet 192.168.10.0/24.

  2.

  The committed information rate must be 54000 pps.

  3.

  The burst size must be 128 packets.

  4.

  Any other traffic must be dropped.

  Drag and drop the code snippets from the bottom onto the blanks in the code on the top to complete the configuration. Not all code snippets are used.

  Select and Place:

  

  Correct Answer:

  

• Question 52:

  DRAG DROP

  A network engineer must implement a telemetry solution to collect real-time structured data in a large-scale network. Drag and drop the actions from the left into the order on the right to implement the solution. Not all actions are used.

  Select and Place:

  

  Correct Answer:

  

  switch# show running-config | section telemetry feature telemetry telemetry destination-group 100 ip address 1.2.3.4 port 50004 protocol gRPC encoding GPB sensor-group 100 path sys/bgp/inst/dom-default depth 0 subscription 600 dst-grp 100 snsr-grp 100 sample-interval 7000

  switch# show running-config | section telemetry > telemetry_running_config

  switch# show file bootflash:telemetry_running_config feature telemetry telemetry destination-group 100 ip address 1.2.3.4 port 50004 protocol gRPC encoding GPB sensor-group 100 path sys/bgp/inst/dom-default depth 0 subscription 600 dst-grp 100 snsr-grp 100 sample-interval 7000

  switch#

• Question 53:

  DRAG DROP

  Drag and drop the Hyperflex characteristics from the left onto the appropriate Hyper Hex node types on the right.

  Select and Place:

  

  Correct Answer:

  

• Question 54:

  DRAG DROP

  An engineer must configure an LACP port channel on two Cisco Nexus 7000 Series Switches.

  The interface e1/2 must be a hot-standby link that initiates negotiation with other ports.

  Drag and drop the commands from the right onto the blanks in the configuration on the left.

  Not all commands are used.

  Select and Place:

  

  Correct Answer:

  

• Question 55:

  DRAG DROP Refer to the exhibit.

  

  An administrator must complete the unified fabric configuration between Server1 and a pair of Cisco Nexus 9000 Series Switches.

  Drag and drop the code snippets from the right onto the blanks in the code on the left to complete the N9K-1 configuration Snippets are used more than once.

  Select and Place:

  

  Correct Answer:

  

  The following example shows how to configure the VLAN on a physical Ethernet address, create virtual Fibre Channel interface 4, bind vfc 4 to the physical Ethernet interface, enable associated VLAN 200, and map VLAN 200 to VSAN 2: switch# configure terminal switch(config)# interface ethernet 1/2

  switch(config-if)# switchport mode trunk

  switch(config-if)# switchport trunk allowed vlan 1,200

  switch(config)# interface vfc 4

  switch(config-if)# bind interface ethernet 1/2

  switch(config-if)# exit

• Question 56:

  DRAG DROP

  

  The server is sending traffic to the storage server using Fiber Channel protocol. The requirement is for the N5K-1 to forward traffic to MDS9k-1. Drag and drop the configuration steps from the right to complete the configuration for N5K-1 on the left. Not all configuration steps are used.

  Select and Place:

  

  Correct Answer:

  

• Question 57:

  DRAG DROP Refer to the exhibit.

  

  An engineer must provision a VXLAN deployment The OSPF has already been configured as the underlay protocol All BGP configurations will be performed using the template method The deployment must meet these requirements

  The local update source for leaf switches must be loopback 1 The router ID must be the local loopback IP address The external BGP connections must use a template name Drag and drop the configuration snippets from the bottom to complete the configuration

  Select and Place:

  

  Correct Answer:

  

• Question 58:

  DRAG DROP

  An engineer must configure Cisco UCS Manager to accept only HTTPS connections that use TLS 1 2 The cipher security level must be high and the length of the keyring key value must be 2048 bits.

  Drag and drop the code snippets from the right onto the blanks in the code on the left to accomplish these goals. Not all commands are used.

  Select and Place:

  

  Correct Answer:

  

• Question 59:

  DRAG DROP

  An engineer must configure the HSRP protocol to implement redundancy using two Cisco Nexus Series Switches In addition, the HSRP must meet these requirements uk.co.certification.simulator.questionpool.PList@1a00c470.

  Drag and drop the configuration commands from the right to the left to meet the requirements. The commands are used more than once. Not all commands are used.

  Select and Place:

  

  Correct Answer:

  

• Question 60:

  A network engineer must create a script to quickly verify IP reachability for multiple hosts using ping from the Cisco NX-OS switches. The script should use the management VRF and exit the shell after execution. Which script should be used to achieve this objective?

  

  A. Option A

  B. Option B

  C. Option C

  D. Option D

  Correct Answer: D