Cisco 350-080 Online Practice Questions and Exam Preparation

Cisco 350-080 Online Questions & Answers

• Question 111:

  Which three parameters are carried by an iSCSI TCP session? (Choose three.)

  A. control messages
  B. SCSI commands
  C. parameters that specify redundant paths
  D. iSCSI PDUs
  E. primitive signals
  A. control messages
  B. SCSI commands
  D. iSCSI PDUs

• Question 112:

  Which statements are valid for a local SPAN configuration? (Choose two.)

  A. Source and destination interface must be on the same host
  B. Source and destination interfaces can be on different hosts
  C. Destination vEthernet interface can be on a different VLAN than the source
  D. Destination interface can be a physical port
  E. Destination interface cannot be a physical port
  A. Source and destination interface must be on the same host
  D. Destination interface can be a physical port

• Question 113:

  Drag Drop

  Select and Place:

  

  

• Question 114:

  Which two Cisco Nexus 2000 Series Fabric Extenders support FCoE? (Choose two.)

  A. 2248TP
  B. 2232ET-P
  C. 2224TP
  D. 2232PP
  E. 2232TM-E
  D. 2232PP
  E. 2232TM-E

• Question 115:

  Refer to the exhibit.

  

  When a CNA host connects to the virtual interface of the switch, what will happen?

  A. The switch will not initialize because it is in the wrong mode.
  B. The host will negotiate using DCBX and connect properly.
  C. The host will negotiate using DCBX and will change parameters as required, but a shut/no shut is needed on the interface.
  D. The host will not connect. The vFC port number does not match the Ethernet interface.
  A. The switch will not initialize because it is in the wrong mode.

• Question 116:

  The Cisco Nexus 1000v Series switches can configure traditional SPAN sessions. Which three statements about the local SPAN source ports are true? (Choose three.)

  A. It can be configured to monitor the direction of the traffic.
  B. It must be in the same VSAN.
  C. It can be port type Ethernet, virtual Ethernet, or port channel.
  D. It must be in the same VLAN.
  E. It cannot be on a different host VEM as the destination port.
  F. It cannot be a port profile.
  A. It can be configured to monitor the direction of the traffic.
  C. It can be port type Ethernet, virtual Ethernet, or port channel.
  E. It cannot be on a different host VEM as the destination port.

• Question 117:

  Refer to the exhibit.

  

  Company ABC has implemented a Cisco Trustsec domain with an initial Cisco ACS server and Cisco Nexus 7000 CTS-DC. The company plans to extend the domain adding an additional Cisco Nexus 7000 CTS-CORE.

  Which three minimum configurations are required on CTS-Core to join the domain? (Choose three.)

  A. Configure interface "cts dot1x".
  B. Configure TrustSec domain.
  C. Configure feature dot1x and cts.
  D. Configure RADIUS authentication, authorization and accounting.
  E. Configure local device ID and password.
  F. Configure as "non-seed" device.
  C. Configure feature dot1x and cts.
  D. Configure RADIUS authentication, authorization and accounting.
  E. Configure local device ID and password.

• Question 118:

  Which three statements about the Cisco Fibre Channel Domain feature are true? (Choose three.)

  A. The domains are configured on a switch wide basis.
  B. It functions as described in the FC-E standards.
  C. It is responsible for fabric reconfiguration.
  D. It is responsible for domain ID distribution.
  E. It acts as relay agent for the FC ID allocations that are distributed by the Fibre Channel Time Server (ff.ff.fb).
  F. It is responsible for principal switch selection.
  C. It is responsible for fabric reconfiguration.
  D. It is responsible for domain ID distribution.
  F. It is responsible for principal switch selection.

• Question 119:

  Given the following configuration: port-profile type ethernet DATA-UPLINK vmware port-group switchport trunk allowed vlan 1-3967,4048-4093 channel-group auto mode on no shutdown state enabled port-profile type ethernet MGMT-UPLINK vmware port-group switchport trunk allowed vlan 10-12 channel-group auto mode on

  no shutdown state enabled VEMs are seen to be joining and then are lost from the Cisco VSM. How would you resolve this issue?

  A. Remove second NIC from each port profile
  B. Remove VEM from VSM (no vem X), remove NICs, and reinsert
  C. Ensure that VLANs on uplink profiles are not overlapping
  D. Reinstall VEM
  E. Issue the command "module vem X execute vemcmd set pinning module vsm 1"
  C. Ensure that VLANs on uplink profiles are not overlapping

• Question 120:

  Which configuration shows the correct method to correct unified ports in a Cisco nexus 5500 switch?

  A. nexus5500# configure terminal nexus5500 (config)# slot 1 nexus5500 (config-slot)# port 32 type fc nexus5500 (config-slot)# copy running-config startup-config nexus5500 (config-slot)# reload
  B. nexus5500# configure terminal nexus5500 (config)# slot 1 nexus5500 (config)# port 32 type fc nexus5500 (config)# copy running-config startup-config nexus5500 (config)# reload
  C. nexus5500# configure terminal nexus5500 (config)# slot 1 nexus5500 (config-slot)# port 32 type fc
  D. nexus5500# configure terminal nexus5500 (config)# slot 1 nexus5500 (config-slot)# port 32 type unified nexus5500 (config-slot)# copy running-config startup-config nexus5500 (config-slot)# reload
  A. nexus5500# configure terminal nexus5500 (config)# slot 1 nexus5500 (config-slot)# port 32 type fc nexus5500 (config-slot)# copy running-config startup-config nexus5500 (config-slot)# reload