Cisco 350-001 Online Practice Questions and Exam Preparation

Cisco 350-001 Online Questions & Answers

• Question 441:

  On a router, interface S0 is running EIGRPv6, and interface S1 is running OSPFv3. A redistribution command is issued under OSPFv3, redistribute EIGRP 1 metric 20 under ipv6 router ospf 1.

  What will happen after applying this redistribution command?

  A. All routes showing up as D and D EX in the routing table will be redistributed into OSPFv3.
  B. All routes showing up as D, D EX, and C in the routing table will be redistributed into OSPFv3.
  C. All routes showing up as D and D EX in the routing table and the S0 interface will be redistributed into OSPFv3.
  D. All routes showing up as D in the routing table will be redistributed into OSPFv3.
  E. All routes showing up as D EX in the routing table will be redistributed into OSPFv3.
  A. All routes showing up as D and D EX in the routing table will be redistributed into OSPFv3.

• Question 442:

  Which two of these statements about WCCP version 2 are false? (Choose two.)

  A. It allows for the redirection of traffic other than HTTP, including a variety of UDP and TCP traffic.
  B. Only one router can redirect content requests.
  C. Multiple routers can redirect content requests.
  D. It works only with IP networks.
  E. The Cache Engine defines one central "home router" and stores it in its memory.
  F. The Cache Engine defines one central "home router," and stores it in its memory.
  B. Only one router can redirect content requests.
  F. The Cache Engine defines one central "home router," and stores it in its memory.

• Question 443:

  The EtherChannel between your LAN switch and the Internet router is not load-balancing efficiently. On the switch, there are several workstations with valid IP ranges.

  Which load-balance algorithms can you use in the switch in order to optimize this load balancing? (Choose four.)

  A. source IP address
  B. destination IP address
  C. per-packet load balance
  D. destination MAC address
  E. source MAC address
  A. source IP address
  B. destination IP address
  D. destination MAC address
  E. source MAC address

• Question 444:

  You have done a partial migration from 802.1D STP to 802.1w STP.

  Which of the following is true?

  A. 802.1 D and 802.1w intemperate only when the 802.1 D STP domain supports rapid convergence.
  B. Ports leading to 802.1D devices will run in compatibility mode, while the rest of the ports will run in 802.1w mode.
  C. This is an invalid configuration and a partial migration cannot be done.
  D. The bridge timers will be set to match the 802.1 D devices.
  E. A secondary root bridge will always be populated within the 802.1 D domain.
  F. If the root bridge is selected within the 802.1 D domain, the whole STP domain will run in 802.1 D compatibility mode.
  G. In partially migrated 802.1w networks, it is recommended to keep the STP diameter below 4.
  B. Ports leading to 802.1D devices will run in compatibility mode, while the rest of the ports will run in 802.1w mode.

• Question 445:

  Refer to the exhibit.

  

  Based on the configuration, what will be the final OSPFv3 neighborship state of R1 and R2?

  A. Both routers will be stuck in init state.
  B. Both routers will be stuck in two-way state.
  C. Both routers will be stuck in exstart/exchange state.
  D. Both routers will be in full (DR or BDR) state.
  C. Both routers will be stuck in exstart/exchange state.

• Question 446:

  What is the purpose of an explicit "deny any" statement at the end of an ACL?

  A. none, since it is implicit
  B. to enable Cisco lOS IPS to work properly; however, it is the deny all traffic entry that is actually required
  C. to enable Cisco lOS Firewall to work properly; however, it is the deny all traffic entry that is actually required
  D. to allow the log option to be used to log any matches
  E. to prevent sync flood attacks
  F. to prevent half-opened TCP connections
  D. to allow the log option to be used to log any matches

• Question 447:

  Refer to the exhibit. Based on the configuration shown, which queuing mechanism has been configured on interface serial.1/0?

  

  A. PQ
  B. CQ
  C. WFQ
  D. LLQ
  E. CBWFQ
  E. CBWFQ

• Question 448:

  Refer to the exhibit. You are investigating connectivity issues on your LAN and have noticed that sometimes you cannot use Telnet from RTA to RTB. Sometimes, Telnet sessions will disconnect on RTA with the message "connection reset by peer." However, you can ping from RTA to RTB at all times.

  What is most likely the cause of this issue?

  

  A. Quality of service is configured on RTA, limiting the Telnet sessions.
  B. Quality of service is configured on RTB, limiting the Telnet sessions.
  C. Control Plane Policing is configured on RTB, limiting the Telnet sessions.
  D. On router RTB, the "login block" mode went to a "quiet period" for the IP address of RTA.
  E. Another device that is connected to the switch is using the same IP address as RTB.
  F. Another device that is connected to the switch is using the same MAC address as RTB.
  E. Another device that is connected to the switch is using the same IP address as RTB.

• Question 449:

  For which IP SLA test type is an IP SLA responder required on the target device?

  A. Path-echo
  B. Path-jitter
  C. An IP SLA responder is not required for any of these probes.
  D. Udp-echo
  E. Tcp-connect
  F. HTTP
  C. An IP SLA responder is not required for any of these probes.

• Question 450:

  Which two types of QoS functionality will be provided by Network-Based Application Recognition? (Choose two.)

  A. NBAR provides the ability to configure MCQ; it is a mandatory MCQ component.
  B. NBAR provides deep packet inspection and is used for advanced packet classification.
  C. NBAR provides per-protocol packet and byte accounting functionality; it is used to track bandwidth utilization for all protocols described in the loaded PDLMs.
  D. NBAR provides scheduling in an MQC policy map using an advanced algorithm.
  B. NBAR provides deep packet inspection and is used for advanced packet classification.
  C. NBAR provides per-protocol packet and byte accounting functionality; it is used to track bandwidth utilization for all protocols described in the loaded PDLMs.