Cisco 300-625 Online Practice Questions and Exam Preparation

Cisco 300-625 Online Questions & Answers

• Question 21:

  DRAG DROP

  Drag and drop the mechanisms of Cisco Secure Boot from the left into the correct order on the right.

  Select and Place:

  

  

• Question 22:

  Which two protocols are used to implement SAN telemetry on Cisco MDS switches? (Choose two.)

  A. RPC transport
  B. GPB transport
  C. gRPC transport
  D. gRPC encoding
  E. GPB encoding
  C. gRPC transport
  E. GPB encoding

• Question 23:

  A network engineer must run a core Cisco Nexus 9500 Series Switch as a POAP server for all top-of-rack Cisco Nexus switches. Which two network functions must run to provide the POAP service? (Choose two.)

  A. DNS
  B. PXE
  C. BOOTP
  D. TFTP
  E. DHCP
  D. TFTP
  E. DHCP

• Question 24:

  Which configuration is available only in Cisco DCNM-SAN Advanced mode?

  A. IVR
  B. VMpath configuration
  C. zoning
  D. template-based provisioning
  A. IVR

• Question 25:

  Refer to the exhibit.

  

  A network engineer must configure the SAN telemetry streaming feature to stream statistics form a Cisco MDS 9000 Series Switch to two external receivers with the IP addresses 192.168.1.4 and 192.168.1.5. Which two configurations accomplish this configuration? (Choose two.)

  A. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 100.
  B. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 300.
  C. Add dst-grp 200 under subscription 100.
  D. Add dst-grp 300 under subscription 200.
  E. Add dst-grp 100 under subscription 200.
  A. Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 100.
  C. Add dst-grp 200 under subscription 100.

• Question 26:

  Which feature on MDS platforms ensures that the code that is running on the hardware platform is authentic and unmodified, while also validating the BIOS to eliminate any rootkits.

  A. Cisco Secure Boot
  B. UEFI Secure Boot
  C. Secure Unique Device Identifier
  D. BIOS Secure Boot
  A. Cisco Secure Boot

• Question 27:

  Which Cisco NX-OS command displays the VSAN that is associated with each FCID?

  A. show fcdomain
  B. show fc2 plogi
  C. show vsan database
  D. show flogi database
  A. show fcdomain

• Question 28:

  Which configuration is always required when running the setup utility on a Cisco MDS 9000 Series Switch?

  A. administrator password
  B. management IP address
  C. active NTP server
  D. active default gateway
  A. administrator password

• Question 29:

  Refer to the exhibit.

  

  The san-user must configure FSPF on the VSAN 500, but fails. An operator with network administrative rights must authorize the san-user to perform this work. Which configuration must the operator apply?

  A. MDS-A(config)# role name sangroup MDS-A(config-role)# no rule 2
  B. MDS-A(config)# role name sangroup MDS-A(config-role)# rule 4 permit config feature fspf
  C. MDS-A(config)# role name sangroup MDS-A(config-role)# rule 2 permit config feature vsan
  D. MDS-A(config)# role name sangroup MDS-A(config-role)# vsan policy deny MDS-A(config-role-vsan)# permit vsan 500
  D. MDS-A(config)# role name sangroup MDS-A(config-role)# vsan policy deny MDS-A(config-role-vsan)# permit vsan 500

• Question 30:

  A storage administrator wants to enable NPV in a Fibre Channel edge switch. Which configuration is supported in this mode?

  A. Cisco Fabric Services distribution over Fibre Channel
  B. E Port connectivity to the core switch
  C. local switching of east-west traffic
  D. Dynamic Port VSAN Membership
  A. Cisco Fabric Services distribution over Fibre Channel