Cisco 300-615 Online Practice Questions and Exam Preparation

Cisco 300-615 Online Questions & Answers

• Question 101:

  In Cisco UCS Central you have a certificate that has the status set to Not Yet Valid. Which scenario could cause the issue?

  A. The certificate field is empty.
  B. The time is incorrectly synchronized.
  C. The trusted point uses a bundled certificate that has a minimum depth of 10.
  D. The certificate is issued by a different trusted point.
  B. The time is incorrectly synchronized.

  ---

• Question 102:

  Refer to the exhibit.

  

  A customer network uses OSPFv2 and MP-BGP protocols A network administrator installs a new Cisco Nexus Switch in the data center but experiences a BGP RIB failure Which action solves the issue?

  A. Change the administrative distance of OSPF to 220
  B. Configure the route as a BGP backdoor
  C. Use a filter list for OSPF to filter both routes
  D. Implement next-hop-self
  D. Implement next-hop-self

  ---

• Question 103:

  A request to activate the port security database is rejected. Which action do you perform to investigate the cause of the issue?

  A. Enable the auto-learning feature.
  B. Use the force option to identify rejected devices.
  C. Find conflicting entries between the active and configuration databases.
  D. Verify that devices are fully attached to the active database.
  B. Use the force option to identify rejected devices.

  ---

• Question 104:

  Refer to the exhibit.

  

  An engineer monitors a Cisco UCS server logs and discovers a blade discovery issue. Which procedure resolves the issue?

  A. 1. Verify the server power module. 2. Decommission the faulty module. 3. Insert a new power module. 4. Recommission the new module.
  B. 1. Verify that server platform power is failed 2. Resolve the platform power issue. 3. Reboot the server. 4. Recommission the server.
  C. 1. Verify the FSM status on the server. 2. Decommission the impacted server. 3. Reset the slot where the server is located. 4. Recommission the server.
  D. 1. Verify that the power on self-test operation is failed. 2. Verify that the server firmware is corrupted. 3. Decommission the server firmware 4. Recommission the server with new firmware.
  C. 1. Verify the FSM status on the server. 2. Decommission the impacted server. 3. Reset the slot where the server is located. 4. Recommission the server.

  ---

  https://www.cisco.com/c/en/us/support/docs/servers-unified-computing/unified-computing-system/214047-troubleshooting-ucs-blade-discovery-issu.pdf

• Question 105:

  Refer to the exhibit.

  

  A blade that is connected to FI-B fails to boot from a SAN LUN. The boot policy is configured to boot by using vHBA1 as the SAN Primary. Which set of actions resolves the issue?

  A. Set VSAN to 20 in vHBA_SAN_B Template. Configure ESX01_B zone to VSAN 20.
  B. Set ESX01_B zone to VSAN 20. Create a new vHBA and assign VSAN 20.
  C. Change vHBA1 to VSAN 20 in Service Profile. Apply VMware Adapter Policy on vHBA1.
  D. Apply VMware Adapter Policy on vHBA1. Change vHBA1 to VSAN 20 in Service Profile.
  A. Set VSAN to 20 in vHBA_SAN_B Template. Configure ESX01_B zone to VSAN 20.

  ---

• Question 106:

  A customer has a Cisco UCS Center cluster. The customer configures LDAP as the AAA protocol and enables SSL for LDAP. The LDAP authentication fails. Which issue is the cause of the failure?

  A. The LDAP client passed an incorrect from the trustpoint.
  B. The ca certificate is missing from the trustpoints.
  C. The LDAP server limit that is set by an administrative authority was exceeded.
  D. The LDAP time limit that is specified by either the client or the server was exceeded.
  B. The ca certificate is missing from the trustpoints.

  ---

• Question 107:

  A server fails to boot from the operating system after a RAID1 cluster migration. The RAID remains in an inactive state during and after a service profile association. Which action resolves the issue?

  A. Configure the SAN boot target in the service profile.
  B. Configure the SAN boot target to any configuration mode.
  C. Use a predefined local disk configuration policy.
  D. Remove the local disk configuration policy.
  C. Use a predefined local disk configuration policy.

  ---

• Question 108:

  An engineer removes a VMM domain from an endpoint group called EPG-1, but the distributed port group fails to be deleted. Which action must be taken to resolve the issue?

  A. Remove the port group manually.
  B. Migrate all virtual machines in the EPG-1 to different hypervisors.
  C. Remove the remaining EPGs from the VMM domain.
  D. Migrate all virtual machines in the EPG-1 to different port groups.
  C. Remove the remaining EPGs from the VMM domain.

  ---

• Question 109:

  

  Refer to the exhibit. A network engineer fails to install applications in a newly deployed Guest Shell on a Cisco Nexus 9000 Series Switch. Which action in the Guest Shell resolves the issue?

  A. Configure the mgmt0 IP address
  B. Install the networking RPM before the PIP install
  C. Add a domain and name server to the resolv.conf file.
  D. Define the management VRF
  C. Add a domain and name server to the resolv.conf file.

  ---

• Question 110:

  A network engineer performs a remote firmware upgrade in a Cisco UCS environment. The I/O module on the secondary fabric interconnects becomes inaccessible during the upgrade. There is no physical access to the chassis to reseat the I/O module. Which action resolves the issue?

  A. Reset the peer I/O module.
  B. Activate Fault Suppression.
  C. Acknowledge the I/O module.
  D. Enable the firmware package.
  A. Reset the peer I/O module.

  ---