Cisco 300-365 Online Practice Questions and Exam Preparation

Cisco 300-365 Online Questions & Answers

• Question 81:

  An engineer must ensure that clients on an 802.1x WLAN can roam as fast as possible at a remote site that was deployed with FlexConnect. Which configuration ensures that this roaming occurs?

  A. FlexConnect group
  B. FlexConnect ACL
  C. learn client IP address
  D. AAA override
  A. FlexConnect group

• Question 82:

  A network engineer is designing a high capacity WLAN for a conference area. The enterprise is concerned about non-business traffic consuming excessive bandwidth and impacting performance. What can be used in the design to allow the controller to block or throttle applications?

  A. AVC
  B. CMX
  C. DSCP
  D. RXSOP
  A. AVC

• Question 83:

  Which of the following is not a Cisco RF fingerprinting key advantage over Location Tracking?

  A. Uses existing LWAPP-enabled Cisco Unified Networking components.
  B. Proprietary client hardware or software is required.
  C. Better accuracy and precision.
  D. Reduced calibration effort.
  B. Proprietary client hardware or software is required.

  ---

  http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Mobility/emob41dg/emob41dg-wrapper/ch13Loca.html#wp1050240

• Question 84:

  Your network has these characteristics: CAC mode is set to load-based CAC The bandwidth usage is between 75 and 85 percent The reserved bandwidth for voice calls is exhausted

  Which action occurs to TSPEC requests in this environment?

  A. The normal TSPEC request is rejected and the expedited bandwidth request is admitted
  B. The normal TSPEC request is admitted and the expedited bandwidth request is rejected
  C. The normal TSPEC request is rejected and the expedited bandwidth request is rejected
  D. The normal TSPEC request is admitted and the expedited bandwidth request is admitted
  A. The normal TSPEC request is rejected and the expedited bandwidth request is admitted

• Question 85:

  A customer called into the support center with a problem ticket that involves wireless clients having to reauthenticate when they are walking around their office. After further investigation, it was discovered that the customer has two controllers in an N+1 deployment. Which action must the engineer take to troubleshoot the issue?

  A. Verify that the wireless controllers are in the same mobility group and that the access points are all on the primary controller.
  B. Under the SSID, make sure that 802.11r is configured and running for the clients.
  C. Make sure that the SSID has the authentication set to 802.1x with Cisco Centralized Key Management so the data clients can roam seamlessly.
  D. Verify the access points are spread out between the primary and secondary controller and that the controllers are in the same mobility group.
  D. Verify the access points are spread out between the primary and secondary controller and that the controllers are in the same mobility group.

• Question 86:

  A FlexConnect remote office deployment is using five 2702i APs indoors and two 1532i APs outdoors. When a code upgrade is performed and FlexConnect Smart AP Image Upgrade is leveraged, but no FlexConnect Master A has been configured. How many image transfers between the WLC and APs will occur?

  A. 7
  B. 1
  C. 5
  D. 2
  D. 2

• Question 87:

  What is the best practice for setting the WLC v7.0 use of WLAN QoS settings to support SIP phones on a VoWLAN?

  A. Configure SIP with static CAC only with SIP call snooping.
  B. Configure SIP with static CAC only without SIP call snooping.
  C. Configure SIP with load-based CAC only with SIP call snooping.
  D. Configure SIP with load-based CAC only without SIP call snooping.
  E. Configure SIP with load-based CAC and TSPEC only with SIP call snooping.
  A. Configure SIP with static CAC only with SIP call snooping.

• Question 88:

  Which feature must be enabled on a WLC to ensure that ARP, DHCP, and data traffic can be forwarded to wired clients located behind non-Cisco workgroup bridges?

  A. Layer 3 roaming
  B. the VLAN select feature for WGB clients
  C. the passive client feature
  D. Layer 3 security web authentication
  C. the passive client feature

• Question 89:

  An engineer has installed a new voice WLAN. Which three configurations would the engineer verify for QoS on the controller? (Choose three.)

  A. client load balancing
  B. DHCP address assignment required
  C. Platinum QoS for the VoWLAN
  D. IEEE 802.1X and Cisco Centralized Key Management
  E. WMM allowed
  F. client band select
  A. client load balancing
  C. Platinum QoS for the VoWLAN
  E. WMM allowed

  ---

  Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-3/config-guide/b_cg83/b_cg83_chapter_0100010.pdf

• Question 90:

  A customer called with a requirement that internal clients must be on different subnets depending on the building they are in. All access points are operating in local mode and will not be modified, and this is a single controller solution. Which configuration change creates the desired result?

  A. Set the SSID to the desired VLAN under WLANs, configure 802.1x in ACS to assign the correct VLAN based on the SSID the client is authenticating from.
  B. Create AP groups for each desired location, map the correct VLANs to the internal SSID, and add the access points for that location.
  C. Configure the access points in the FlexConnect mode and set the correct VLAN to SSID mapping based on location.
  D. Create mobility anchors for the SSID, and on the controller under the internal SSID, create a foreign map to the desired VLAN based on location.
  A. Set the SSID to the desired VLAN under WLANs, configure 802.1x in ACS to assign the correct VLAN based on the SSID the client is authenticating from.