Cisco 300-365 Online Practice Questions and Exam Preparation

Cisco 300-365 Online Questions & Answers

• Question 101:

  An organization is planning on concerting remote offices to FlexConnect to centralize their Cisco WLCs. When preparing the Cisco ACLs for the new deployment, which three restrictions must the engineer keep in mind? (Choose three.)

  A. FlexConnect ACLs only
  B. up to 64 rules per ACL
  C. up to 32 rules per ACL
  D. FlexConnect or standard ACLs
  E. all rules applied inbound only
  F. all rules applied in both directions
  A. FlexConnect ACLs only
  B. up to 64 rules per ACL
  E. all rules applied inbound only

• Question 102:

  A customer has configured a wireless LAN controller and set the 802.11a/n data rates. All rates are enabled where 5.5 Mbps, 11Mbps, and 24 Mbps are set to Mandatory. What will APs send over the 24 Mbps data rate?

  A. channel announcements
  B. DTPC support
  C. multicast broadcast
  D. beacons
  C. multicast broadcast

• Question 103:

  A network engineer is experiencing issues enabling LAG on the WLC. Which four characteristics should be validated to ensure LAG configuration? (Choose four.)

  A. ll ports participate in the LAG by default when LAG is enabled on the controller. y
  B. Dynamic interfaces and management are moved to port 1
  C. Primary and secondary ports are needed for each interface.
  D. Multiple untagged interfaces to the same port are not allowed.
  E. EtherChannel must be configured for mode "on" on the switch.
  F. Only one functional physical port is needed to continue to pass traffic.
  G. Multiple LAGs are permitted on the controller.
  H. The WLC does not need to be rebooted to enable the LAG configuration.
  A. ll ports participate in the LAG by default when LAG is enabled on the controller. y
  D. Multiple untagged interfaces to the same port are not allowed.
  E. EtherChannel must be configured for mode "on" on the switch.
  F. Only one functional physical port is needed to continue to pass traffic.

  ---

  http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_0100011.html

• Question 104:

  A wireless engineer wants to enable optimized roaming for their 5GHz wireless network with these settings: -72dBm RSSI value, 25% coverage exception level percentage, and a minimum of 50 packets received.

  Which two commands achieve these settings? (Choose two.)

  A. config advanced 802.11a coverage data fail-percentage 25
  B. config advanced 802.11b optimized-roaming enable
  C. config advanced 802.11b coverage data rssi-threshold -72
  D. config advanced 802.11a optimized-roaming enable
  E. config advanced 802.11a coverage data rssi-threshold -72
  A. config advanced 802.11a coverage data fail-percentage 25
  D. config advanced 802.11a optimized-roaming enable

• Question 105:

  You plan to use Cisco Centralized Key Management fast roaming with FlexConnect APs. Which configuration do you apply to minimize delays for real-time traffic while roaming?

  A. FlexConnect groups
  B. FlexConnect local authentication
  C. FlexConnect AVCs
  D. FlexConnect centralized authentication
  A. FlexConnect groups

• Question 106:

  A customer is implementing a massively scaled guest wireless network to support approximately 32,000 clients. For ease of administration, they have required implementing multiple interfaces defined on the WLC and mapped to a single interface group. Which configuration meets this need?

  A. 264 interfaces of /25 sized networks
  B. 132 interfaces of /24 sized networks
  C. 66 interfaces of /23 sized networks
  D. 33 interfaces of /22 sized networks
  D. 33 interfaces of /22 sized networks

  ---

  References: http://www.cisco.com/c/en/us/support/docs/wireless/8500-series-wireless-controllers/113695-8500-dg-00.html

• Question 107:

  A network engineer has installed 802.11ac access points with 80 MHz enabled; however, in the conference rooms, co-channel interference is being noticed. Under which tab in the RF profiles configuration can the engineer find the settings to tune the channel width for a group of APs?

  A. 802.11
  B. RRM
  C. High Density
  D. General
  B. RRM

  ---

  http://www.cisco.com/c/dam/en/us/td/i/400001-500000/400001-410000/403001-404000/403466.tif/_jcr_content/renditions/403466.jpg

• Question 108:

  A wireless engineer is configuring a Cisco MSE by using the automatic installation script. Which two parameters are mandatory and must be configured at least once? (Choose two.)

  A. Ethernet interface
  B. hostname
  C. GRUB password
  D. domain name
  E. NTP server
  A. Ethernet interface
  B. hostname

  ---

  Please note that the following parameters (indicated by *) are mandatory and must be configured at least once. -> Hostname -> Network interface eth0 -> Timezone -> Root password -> NCS Communication username -> NCS Communication password

  Reference: https://www.cisco.com/c/en/us/td/docs/wireless/mse/7-6/Virtual_appliance/Installation_Config_Guide/Cisco_MSE_VA_Config_Guide/Installing_MSE_Virtual_Appliance.html

• Question 109:

  Which CLI command does a wireless engineer use to display the maximum number of hops?

  A. show ap config general
  B. show mesh statistics
  C. show mesh hop-count
  D. show mesh config
  D. show mesh config

• Question 110:

  You have Microsoft Lync, which uses an 802.1p table instead of an 802.11e table for tagging the VoWiFi packets. Which configuration must be used to utilize the priority queue and preserve the correct voice packet marking as EF on a Cisco Catalyst switch?

  A. Run the mls qos command and trust either CoS or DSCP
  B. Run the no mls qos command and trust nothing on switchport
  C. Run the mls qos command and trust CoS
  D. Run the mls qos command and trust DSCP only
  D. Run the mls qos command and trust DSCP only