Cisco 300-360 Online Practice Questions and Exam Preparation

Cisco 300-360 Online Questions & Answers

• Question 101:

  A network engineer is retrofitting an existing building wired with Category 5e with AP 3800 and mGig switches. Which cable length allows for 5G operation?

  A. 70 m
  B. 120 m
  C. 130 m
  D. 150 m
  A. 70 m

• Question 102:

  You are using the Voice Readiness tool in the Cisco Prime Infrastructure for a customer who needs to deploy Cisco IP phones. Which dBm range is evaluated by the Voice Readiness tool?

  A. -72 to -65
  B. -85 to -67
  C. -75 to -60
  D. -75 to -67
  B. -85 to -67

• Question 103:

  An engineer is implementing Q0S for a new wireless voice network. Which two considerations should be identified first? (Choose two.)

  A. QoS marking
  B. policing
  C. QoS requirements
  D. data traffic usage
  E. traffic classification
  C. QoS requirements
  E. traffic classification

• Question 104:

  An engineer would like to calibrate the RF environment to improve accuracy. Which wireless attribute is added to the floor-level calculation by calibrating the floor?

  A. attenuation
  B. TX power
  C. multipath
  D. SNR
  A. attenuation

• Question 105:

  IEEE 802.11r-2008 or fast BSS transition (FT), also called "fast roaming," Which 802.11 standard performs the PTK calculations in advance to enable fast client roaming?

  A. 802.1 11r
  B. 802.1 11i
  C. 802.1 11k
  D. 802 1 11w
  A. 802.1 11r

  ---

  802.11r, which is the IEEE standard for fast roaming, introduces a new concept of roaming where the initial handshake with the new AP is done even before the client roams to the target AP, which is called Fast Transition (FT). The initial handshake allows the client and APs to do the Pairwise Transient Key (PTK) calculation in advance. These PTK keys are applied to the client and AP after the client does the reassociation request or response exchange with new target AP. https://www.cisco.com/c/en/us/td/docs/wireless/controller/technotes/80211r-ft/b-80211r-dg.html

• Question 106:

  An engineer is deploying an outdoor Mesh network. Which four major factors should be considered? (Choose four.)

  A. power
  B. buildings
  C. traffic lights
  D. satellite dishes
  E. line of sight
  F. network connectivity
  G. power lines H. mounting
  A. power
  B. buildings
  E. line of sight

• Question 107:

  Which tool do you use to identify microwaves and Bluetooth devices when designing a WLAN?

  A. AirMagnet Survey
  B. EDRRM
  C. Ekahau Site Survey
  D. MetaGeek Chanalyzer
  A. AirMagnet Survey

• Question 108:

  An engineer must design a wireless voice network and is auditing the existing configuration. Which two actions must be taken? (Choose two.)

  A. Enable Platinum QoS profile on the SSID
  B. Disable Coverage Hole Detection.
  C. Ensure the switch ports trust DSCP QoS markings
  D. Disable WMM on the QoS tab
  E. Ensure that Client Load Balancing is enabled.
  A. Enable Platinum QoS profile on the SSID
  C. Ensure the switch ports trust DSCP QoS markings

  ---

  https://mrncciew.com/2012/11/28/understanding-wireless-qos-part-1/

• Question 109:

  The AP has been configured property for a VoWLAN survey The RF environment contains a noise of -87 to -90 dBm. What is the target value for the cell edge reading?

  A. -62 dBm
  B. -67 dBm
  C. -60 dBm
  D. -70 dBm
  B. -67 dBm

  ---

  Reference: http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-1/Enterprise-Mobility-8-1-Design-Guide/Enterprise_Mobility_8-1_Deployment_Guide/Chapter-9.html

• Question 110:

  Which option is an enhancement of enabling WMM on an AP?

  A. All access classes use the same IEEE 802.11 sequence number.
  B. It disables U-APSD Power Save.
  C. Each access class has its own IEEE 802.11 sequence number.
  D. CAC is reserved for voice calls only.
  C. Each access class has its own IEEE 802.11 sequence number.