Cisco 300-360 Online Practice Questions and Exam Preparation

Cisco 300-360 Online Questions & Answers

• Question 121:

  An engineer is installing a wireless network in an industrial area with extreme temperatures and a significant amount of dust. Which enclosure should be used to protect the APs?

  A. ACU
  B. ADU
  C. NEMA
  D. WLSE
  C. NEMA

  ---

  Sometimes access points (APs) are located in areas where they are subject to extreme moisture, temperatures, dust and particles. These APs might need to be mounted inside a sealed enclosure. The NEMA has a rating system for these enclosures, which are generally called NEMA enclosures. Reference: http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/68666-wireless-site-survey-faq.html

• Question 122:

  An engineer is preparing for an active site survey of a hospital and is informed that he or she should not enter any active surgery suites. Which option describes how the engineer should address this restriction?

  A. Conduct a passive wireless survey in the restricted areas.
  B. Use the predictive AP placement tool on the wireless controller
  C. Skip the area and estimate where to place the access points.
  D. Arrange to perform survey activities after hours.
  A. Conduct a passive wireless survey in the restricted areas.

  ---

  Passive Survey Passive surveys are surveys that are performed with a listen-only mode. The survey client never associates to the access point (AP). Such surveys can be helpful when you look for rogue devices or you want a good gauge of downlink RF coverage from the infrastructure devices. These can be accomplished with a passive survey.

• Question 123:

  Which three components and tasks should be considered while planning the site survey? (Choose three.)

  A. Determine the project scope, type of deployment, timeline, scale, budget, and users
  B. Determine project stakeholders
  C. Determine customer training requirements
  D. Determine AP and controller placement
  E. Determine the customer applications that the network will support
  F. Determine radio spectrum and channel allocation
  G. Schedule customer end user interviews
  A. Determine the project scope, type of deployment, timeline, scale, budget, and users
  B. Determine project stakeholders
  E. Determine the customer applications that the network will support

• Question 124:

  You are using the Cisco Aironet 3800 Series access points connected to Cisco Catalyst 3850 switches and you want to use the multi-Gigabit Ethernet feature. Which cable category is the minimum requirement for the wired infrastructure to have support of this feature?

  A. Cat5e
  B. Cat6
  C. Cat6e
  D. Cat5
  A. Cat5e

• Question 125:

  A customer has determined that aesthetics is a primary concern for their upcoming guest deployment. Which design consideration can be leveraged to address this concern?

  A. Paint the access point to cover the LED from being noticeable
  B. Use enclosures to hide the wireless infrastructure in the surrounding environment
  C. Deploy environmentally friendly cabling components to blend into the environment.
  D. Use AIR-AP-BRACKET-1 to allow for greater mounting locations
  C. Deploy environmentally friendly cabling components to blend into the environment.

• Question 126:

  When designing and deploying an outdoor mesh network, what is the appropriate RF cell overlap?

  A. 10 percent
  B. 15 percent
  C. 20 percent
  D. 25 percent
  E. Application dependent
  E. Application dependent

• Question 127:

  Refer to the exhibit. An engineer has determined that Cisco 7925 phones are roaming between 2.4 6Hz and 5 6Hz radios on the same access points, which results in poor audio performance Which action must the engineer take to mitigate this issue?

  

  A. Enable TPCv2 to normalize the RF environment.
  B. Configure EDCA parameters for Voice Optimized.
  C. Configure the Cisco 7925 phone to only use 5 6Hz.
  D. Enable Band Select on the WLAN
  B. Configure EDCA parameters for Voice Optimized.

• Question 128:

  You must redesign an existing wireless network that spans multiple floors to support location-based services. Where do you install the access points?

  A. in the elevators
  B. in the perimeter of each floor
  C. in the stairwells of each floor
  D. in the center of each floor
  D. in the center of each floor

• Question 129:

  When implementing video teleconferencing over a wireless network, which three attributes should be considered when cell planning? (Choose three.)

  A. latency
  B. jitter
  C. throughput
  D. packet loss
  E. client association
  F. number of users on the network
  A. latency
  B. jitter
  D. packet loss

• Question 130:

  You are designing a WLAN by using the capacity planner in Ekahau Site Survey. What is the maximum Peak Hour Usage setting that you can configure?

  A. 2x
  B. 6x
  C. 8x
  D. 12x
  C. 8x