Cisco 300-101 Online Practice Questions and Exam Preparation

Cisco 300-101 Online Questions & Answers

• Question 421:

  Which option is one way to mitigate symmetric routing on an active/active firewall setup for TCP-based connections?

  A. performing packet captures
  B. disabling asr-group commands on interfaces that are likely to receive asymetric traffic
  C. replacing them with redundant routers and allowing load balancing
  D. disabling stateful TCP checks
  D. disabling stateful TCP checks

• Question 422:

  Which two statements about the OSPF down bit are true? (Choose two)

  A. It is set only for LSA types 3,5. and 7
  B. It is set only for LSA types 1, 2 and 4
  C. It is set only when an OSPF virtual link is created
  D. It is set when MP-BGP routes are redistributed into OSPF
  E. It is set when OSPF routes are redistributed into BGP
  A. It is set only for LSA types 3,5. and 7
  D. It is set when MP-BGP routes are redistributed into OSPF

• Question 423:

  Refer to the following command: router(config)# ip http secure-port 4433 Which statement is true?

  A. The router will listen on port 4433 for HTTPS traffic.
  B. The router will listen on port 4433 for HTTP traffic.
  C. The router will never accept any HTTP and HTTPS traffic.
  D. The router will listen to HTTP and HTTP traffic on port 4433.
  A. The router will listen on port 4433 for HTTPS traffic.

• Question 424:

  A network engineer is migrating an IPv4 point-to-multipoint Frame Relay network to IPv6.

  Which IPv6 address type must be used in a Frame Relay map configuration command to ensure that the OSPF protocol still works after migration?

  A. link-local
  B. site-local
  C. unique-local
  D. multicast
  E. global
  A. link-local

• Question 425:

  Which type of address does OSPFv3 uses to form neighbor adjancises and to send LSAs?

  A. unicast addresses
  B. tank-local addresses
  C. unicast IPv4 addresses
  D. unicast address FF02::5
  D. unicast address FF02::5

• Question 426:

  

  Refer to the exhibit. All interfaces on each router are participating in the EIGRP 100 process. Interface Loopback 2 on NQ-R2 is currently in shutdown mode. An engineer issues the eigrp stub command on router BR1. Which statement about the query messages sent from router HQ-R2 for a route to reach the 12.12.12.12/32 network is true?

  A. Router HQ-R1 receives query messages from HQ-R2 for a route to 12.12.12.12/32 network.
  B. Router HQ-R1 and BR1 receives query massages from HQ-R2 for a route 12.12.12.12/32 network.
  C. Router HQ-R2 sends a query message to the feasible successor for a route to 12.12.12.12/32 network
  D. BR1 receives query messages from HQ-R2 for route to 12.12.12.12/32 network
  B. Router HQ-R1 and BR1 receives query massages from HQ-R2 for a route 12.12.12.12/32 network.

• Question 427:

  

  Refer to the exhibit. How will R1 handle the route to network 10.1.60.0/24?

  A. R1 fails to tag the route.
  B. R1 sets a tag of 10.
  C. R1 sets a tag of 30.
  D. R1 sets a tag of 20.
  A. R1 fails to tag the route.

• Question 428:

  which type of information is displayed when a network engineer executes the show track 1 command on the router?

  A. information about tracking list 1.
  B. time to next poll for track object 1.
  C. information about the IP route track table.
  D. tracking information statistics.
  A. information about tracking list 1.

• Question 429:

  A network engineer wants an NTP clients to be able to update the local system without updating or synchronizing with the remote system. Which option for the ntp access-group command is needed to accomplish this?

  A. serve
  B. query-only
  C. serve-only
  D. peer
  A. serve

• Question 430:

  Which two OSPF router types can perform summarize in an OSPF network? (Choose two)

  A. summary router
  B. area border router
  C. autonomous system boundary router
  D. internal router
  E. backbone router
  B. area border router
  C. autonomous system boundary router