Cisco 300-101 Online Practice Questions and Exam Preparation

Cisco 300-101 Online Questions & Answers

• Question 991:

  Which statement is true about 6to4 tunneling?

  A. IPv4 traffic is encapsulated with an IPv6 header
  B. the edge router can use locally configured IPv6 address
  C. host and routers inside a 6to4 site will need a special code
  D. an edge router must use IPv6 address of 2002::/16 in its prefix
  D. an edge router must use IPv6 address of 2002::/16 in its prefix

• Question 992:

  Which type of Cisco Express Forwarding adjacency is created when the next hop is directly connected, but its MAC header rewrite information is missing?

  A. punt
  B. discard
  C. null
  D. glean
  D. glean

• Question 993:

  Which command enables NAT-PT on an IPv6 interface?

  A. IPv6 nat-pt enable
  B. ipv6 nat
  C. ipv6 nat-pt
  D. ipv6 nat enable
  B. ipv6 nat

• Question 994:

  Which statement about dual stack is true?

  A. Dual stack translates IPv6 addresses to IPv4 addresses
  B. Dual stack means that devices are able to run IPv4 and IPv6 in parallel.
  C. Dual stack translates IPv4 addresses to IPv6 addresses
  D. Dual stack changes the IP addresses on hosts from IPv4 to IPv6 automatically
  B. Dual stack means that devices are able to run IPv4 and IPv6 in parallel.

• Question 995:

  What is VRF-Lite?

  A. VRF without independent routing tables
  B. VRF without MPLS
  C. VRF without Cisco Express Forwarding switching
  D. VRF without VPN
  B. VRF without MPLS

• Question 996:

  PPPoE requires certain signals and information to establish, accept, control and terminate the session. The basic signalling is shown below.

  A. (PPPoE Active Discovery Request), PADI (PPPoE Active Discovery Initiation)
  B. (PPPoR Active Discovery Request), PARP (PPPoE Active Discovery Initiation)
  C. (PPPoE Active Discovery Reaching), PADI (PPPoE Active Discovery Initiating)
  D. (PPP Active Discovery Request), PADI (PPP Active Discovery Initiation)
  A. (PPPoE Active Discovery Request), PADI (PPPoE Active Discovery Initiation)

• Question 997:

  Features of Netflow version 9? (Choose two)

  A. IEEE standard
  B. IETF standard
  C. ingress
  D. egress
  E. ingress/egress
  F. Cisco proprietary
  B. IETF standard
  E. ingress/egress

• Question 998:

  There is an exhibit which shows eigrp configured across the 2 Spokes and one Hub router. Question is why the spoke routers are not able to see each others loopback ?

  A. Network mask used on loopback interface of spoke is invalid
  B. Split horizon enabled on Hub is preventing the advertisement
  C. Physical layer 1 issue between the Spoke and Hub
  D. Split horizon on one of the spoke interface is preventing the advertisement
  B. Split horizon enabled on Hub is preventing the advertisement

• Question 999:

  What are three reasons to control routing updates via route filtering? (Choose three).

  A. to hide certain networks from the rest of the organization
  B. for easier implementation
  C. to control network overhead on the wire
  D. for simple security
  E. to prevent adjacencies from forming
  A. to hide certain networks from the rest of the organization
  C. to control network overhead on the wire
  D. for simple security

• Question 1000:

  A network engineer has set up VRF-Lite on two routers where all the interfaces are in the same VRF. At a later time, a new loopback is added to Router 1, but it cannot ping any of the existing interfaces. Which two configurations enable the local or remote router to ping the loopback from any existing interface? (Choose two.)

  A. adding a static route for the VRF that points to the global route table
  B. adding the loopback to the VRF
  C. adding dynamic routing between the two routers and advertising the loopback
  D. adding the IP address of the loopback to the export route targets for the VRF
  E. adding a static route for the VRF that points to the loopback interface
  F. adding all interfaces to the global and VRF routing tables
  A. adding a static route for the VRF that points to the global route table
  B. adding the loopback to the VRF