Cisco 300-080 Online Practice Questions and Exam Preparation

Cisco 300-080 Online Questions & Answers

• Question 311:

  Refer to the exhibit. You are trying to establish a multipoint call via a Cisco TelePresence SX20 that is registered to Cisco Unified Communications Manager. When you attempt to bring a third party into the call, you receive an error that the call cannot be completed. You confirm that your MCU resources are configured correctly on Cisco Unified Communications Manager and that other devices are able to establish multipoint calls. What is the cause of this issue?

  

  A. The multipoint mode should be set to Multiway.
  B. The call protocol should be H.323.
  C. The MCU is at capacity.
  D. The multipoint mode should be set to Cisco Unified Communications Manager Resource Group.
  E. The multipoint mode should be set to None.
  D. The multipoint mode should be set to Cisco Unified Communications Manager Resource Group.

• Question 312:

  An IP phone that is connected through a Cisco Catalyst 3750 Series Switch is failing to register with the subscriber as a backup server. When the user presses the settings button on the phone, only the Cisco Unified Communications Manager publisher shows as registered. What is the most likely cause for this issue?

  A. The phone does not have the correct Cisco Unified Communications Manager group in the device configuration page.
  B. The Cisco Unified Communications Manager group that is applied through the device pool is misconfigured.
  C. The ip-helper address command for the subscriber is not configured on the switch port.
  D. The subscriber does not have the correct device pool configured.
  E. The enterprise phone configuration does not have the call control redundancy enabled.
  B. The Cisco Unified Communications Manager group that is applied through the device pool is misconfigured.

• Question 313:

  Which action can you take to prevent users from transferring external calls to external devices?

  A. Enable the Block OffNet to OffNet Transfer feature in Cisco Unified Communications Manager
  B. Block the National route pattern.
  C. Remove the route pattern to prevent inbound calls from matching the gateway.
  D. Create a new translation pattern to block external call transfer.
  A. Enable the Block OffNet to OffNet Transfer feature in Cisco Unified Communications Manager

• Question 314:

  After you deploy SAF in a mega cluster and you verify that TCP port 5050 is open, you notice that SAF connections are failing. Which two functions must you check to troubleshoot the problem? (Choose Two)

  A. Cisco AXL Web Service
  B. Cisco UP XCP Router Service
  C. Connection Conversation Messenger
  D. SMTP Server
  E. CCD Advertising Service
  F. CCD Requesting Service
  E. CCD Advertising Service
  F. CCD Requesting Service

• Question 315:

  When user attempted to call a colleague at the same site, the caller received a recording that the call could not be completed as dialed. Which two actions can you take to troubleshoot the problem? (Choose two.)

  A. Reboot the IP phone that the user attempted to call.
  B. Verity that the partition and calling search space are correct.
  C. Reboot the user's IP phone.
  D. Reboot the Cisco Unified communications Manager Cluster.
  E. Ping the remote gateway to verify connectivity.
  F. Use RTMT to trace the call from DN to DN.
  B. Verity that the partition and calling search space are correct.
  E. Ping the remote gateway to verify connectivity.

• Question 316:

  As a Voice Administrator, you have configured the Service Advertisement Call Control Discovery (CCD) feature. When you encounter CCD issues, which command would you use on the IOS interface to check all the learned routes on the IOS device?

  A. show eigrp service-family ipv4 topology
  B. show voice safdndb all
  C. show ccm-manager
  D. show eigrp service-family ipv4 interfaces
  E. show voice saf client
  F. show voice saf dial-peer outbound
  B. show voice safdndb all

• Question 317:

  A user gets the following error on the IP phone:

  [205]-User Profile Absent

  What could be the probable cause?

  A. The user profile is missing.
  B. The device profile is not attached to the user.
  C. The Enable Extension Mobility option is not enabled in the phone configuration window.
  D. User ID and password are incorrectly entered on the phone.
  E. User is assigned to another phone.
  F. User is logged on to another phone.
  B. The device profile is not attached to the user.

• Question 318:

  Which two protocols are required for a Cisco 8800 Series IP Phone to successfully register with Cisco Unified Communications manager? (Choose two.)

  A. HTTP
  B. TFTP
  C. DHCP
  D. SCCP
  E. SIP
  D. SCCP
  E. SIP

• Question 319:

  A Cisco phone displays an error message "Not Enough Bandwidth" when attempting a call. Where in Cisco Unified CM can this problem be resolved?

  A. System > Location Info >Location
  B. System > Location Info > Location Bandwidth Manager Group
  C. System > Region Information > Audio Codec Preference List
  D. System > Region Information > Region
  A. System > Location Info >Location

• Question 320:

  Which Cisco Unified Communications Manager tool verifies configured route patterns, calling search spaces, and route groups?

  A. Cisco Unified Reporting
  B. Cisco Unified Communications Manager CDR Analysis and Reporting
  C. Cisco Unified Communications Manager Dialed Number Analyzer
  D. Cisco Unified Real-Time Monitoring Tool
  C. Cisco Unified Communications Manager Dialed Number Analyzer