Cisco 300-080 Online Practice Questions and Exam Preparation

Cisco 300-080 Online Questions & Answers

• Question 361:

  During a conference that is hosted on a Cisco TelePresence Server, which three circumstances determine that some participants do not have video, but they do have audio? (Choose three.)

  A. The participants have no video component.
  B. No free screen licensing ports are available.
  C. No video ports are available in a slave Cisco TelePresence Server configuration.
  D. The maximum number of participants is exceeded.
  E. In all Cisco TelePresence deployments, some participants are connected only via audio.
  F. No video ports are available in a single Cisco TelePresence Server configuration.
  B. No free screen licensing ports are available.
  C. No video ports are available in a slave Cisco TelePresence Server configuration.
  F. No video ports are available in a single Cisco TelePresence Server configuration.

• Question 362:

  After you deploy a new Cisco Collaboration solution, users report echoes and choppy voice quality. Which two actions correct the problem? (Choose two.)

  A. Upgrade the Cisco IOS version and flash memory on the Cisco IOS router.
  B. Deploy additional hardware resources
  C. Deploy an echo canceller.
  D. Upgrade Cisco Unified Communications Manager.
  E. Enable QoS on the network.
  C. Deploy an echo canceller.
  E. Enable QoS on the network.

• Question 363:

  Which issue would cause an MGCP gateway to fail to register with Cisco Unified Communications Manager?

  A. missing the configuration command isdn bind-l3 ccm-manager under the ISDN interface
  B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration
  C. misconfigured route group in Cisco Unified Communications Manager
  D. incorrect MGCP IP address specified in the gateway configuration in Cisco Unified Communications Manager
  B. mismatched domain name on the MGCP gateway and Cisco Unified Communications Manager gateway configuration

• Question 364:

  Which cisco unified communications manager tool can you use to troubleshoot issues with international calling?

  A. Cisco Prime
  B. Cisco Deployment Tool
  C. RTMT
  D. Dialed Number Analyzer
  C. RTMT

• Question 365:

  Some of yours users report issues when they are dialing extensions located in other branch offices. Sometimes the calls are set up successfully, and sometimes users experience problems during call setup. Which two reasons for the issue are true? (Choose two)

  A. Not enough bandwidth is available between the two locations and Automated Alternate Routing is disabled on this cluster.
  B. The Partition that contains the called extensions is not assigned to the line or device CSS of the calling users.
  C. A firewall rule blocks traffic between the branch offices so the call setup cannot be completed.
  D. The called extension is used only on a device profile for extension mobility and the user has been authenticated to a second phone in a different branch so the calls are delivered randomly to only one of his phones.
  E. The remote branch experiences WAN link outages and there is no Forward Unregistered Internal number configured for the remote directory number.
  A. Not enough bandwidth is available between the two locations and Automated Alternate Routing is disabled on this cluster.
  E. The remote branch experiences WAN link outages and there is no Forward Unregistered Internal number configured for the remote directory number.

• Question 366:

  ACME corporation is deploying a new voice gateway. The Network administrator is trying to configure the ISDN PRI T1 cards. However, the router does not accept the controller t10/0/0 command. The administrator sees this message "% Invalid input detected at" "marker". To diagnose this problem, which two commands should the administrator use? (Choose two)

  A. Use the feature activate isdn command
  B. Use the clock source line command
  C. Use the show voice call status command
  D. Use the card type t1 command
  E. Use the show call active voice brief command
  F. Use the show inventory command
  D. Use the card type t1 command
  F. Use the show inventory command

• Question 367:

  Which Cisco Unified Communications Manager troubleshooting tool can be used to look at detailed specific events, such as dial plan digit analysis, as they are happening?

  A. RTMT real-time trace
  B. Cisco Unified Dialed Number Analyzer
  C. syslog output
  D. RTMT performance log viewer
  B. Cisco Unified Dialed Number Analyzer

• Question 368:

  Refer the exhibit. An engineer configured ILS between two Cisco Unified Communications Manager clusters?

  After the configuration is saved, the success screen never appears. Based on the trace output, what is the root cause of this problem?

  

  A. Cisco Tomcat certs are missing on all servers
  B. A firewall between the two clusters is blocking the connection between the servers
  C. ILS password in the spoke server is incorrectly configured
  D. IP address of the hub server is incorrectly configured
  B. A firewall between the two clusters is blocking the connection between the servers

• Question 369:

  A system administrator observes that settings on an endpoint revert to unknown values every day, without the administrator's knowledge. What are two likely causes of this issue? (Choose two.)

  A. Persistent settings on the endpoint are causing the issue.
  B. The TMS reverts the configuration backup of the endpoint.
  C. The external server periodically restores the configuration on the endpoint.
  D. A persistent template is applied for the endpoint on the TMS.
  E. The endpoint can be set to periodically revert to a specific configuration.
  A. Persistent settings on the endpoint are causing the issue.
  B. The TMS reverts the configuration backup of the endpoint.

• Question 370:

  Which database replication value indicates that the server no longer has an active logical connection to receive database tables?

  B. 1
  C. 2
  D. 3
  E. 4
  E. 4