1. Home
  2. Cisco
  3. 200-301

Cisco 200-301 Online Practice Questions and Exam Preparation

200-301 Exam Details

  • Exam Code
    :200-301
  • Exam Name
    :Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1
  • Certification
    :CCNA
  • Vendor
    :Cisco
  • Total Questions
    :1716 Q&As
  • Last Updated
    :Jun 01, 2026

Cisco 200-301 Online Questions & Answers

  • Question 931:

    Refer to the exhibit. What is the next hop for traffic entering R1 with a destination of 10.1.2.126?

    A. 10.165 20.126
    B. 10.165.20.146
    C. 10.165.20.166
    D. 10.165 20.226

  • Question 932:

    What is the difference between IPv6 unicast and anycast addressing?

    A. IPv6 anycast nodes must be explicitly configured to recognize the anycast address, but IPv6 unicast nodes require no special configuration
    B. IPv6 unicast nodes must be explicitly configured to recognize the unicast address, but IPv6 anycast nodes require no special configuration
    C. An individual IPv6 unicast address is supported on a single interface on one node but an IPv6 anycast address is assigned to a group of interfaces on multiple nodes.
    D. Unlike an IPv6 anycast address, an IPv6 unicast address is assigned to a group of interfaces on multiple nodes

  • Question 933:

    Refer to the exhibit.

    A packet is being sent across router R1 to host 172.16.3.14. To which destination does the router send the packet?

    A. 207.165.200.246 via Serial0/1/0
    B. 207.165.200.254 via Serial0/0/0
    C. 207.165 200.254 via Serial0/0/1
    D. 207.165.200.250 via Serial0/0/0

  • Question 934:

    Which two QoS tools provides congestion management? (Choose two)

    A. CAR
    B. CBWFQ
    C. PQ
    D. PBR
    E. FRTS

  • Question 935:

    DRAG DROP

    Refer to the exhibit.

    Drag and drop the destination IPs from the left pnto the paths to reach those destinations on the right.

    Select and Place:

  • Question 936:

    Refer to the exhibit.

    An engineer is configuring a new Cisco switch, NewSW, to replace SW2. The details have been provided:

    1. Switches SW1 and SW2 are third-party devices without support for trunk ports.
    2. The existing connections must be maintained between PC1, PC2, and PC3.
    3. Allow the switch to pass traffic from future VLAN 10.

    Which configuration must be applied?

    A. NewSW(config)#interface f0/0 NewSW(config-if)#switchport mode trunk NewSW(config-if)#switchport trunk native vlan 10 NewSW(config-if)#switchport trunk native vlan 10
    B. NewSW(config)#interface f0/0 NewSW(config-if)#switchport mode access NewSW(config-if)#switchport trunk allowed vlan 2,10 NewSW(config-if)#switchport trunk native vlan 2
    C. NewSW(config)#interface f0/0 NewSW(config-if)#switchport mode access NewSW(config-if)#switchport trunk allowed vlan 2,10 NewSW(config-if)#switchport trunk native vlan 10
    D. NewSW(config)#interface f0/0 NewSW(config-if)#switchport mode trunk NewSW(config-if)#switchport trunk allowed vlan 2,10 NewSW(config-if)#switchport trunk native vlan 2

  • Question 937:

    How are API keys used to enforce rate limiting?

    A. To define the network path the API request should take
    B. To uniquely identify each client application
    C. To specify the type of data format the client prefers to receive
    D. To encrypt data sent in the API request

  • Question 938:

    Refer to the exhibit.

    An administrator must configure interfaces Gi1/1 and Gi1/3 on switch SW11. PC-1 and PC-2 must be placed in the Data VLAN, and Phone-1 must be placed in the Voice VLAN.

    Which configuration meets these requirements?

    A. interface gigabitethernet1/1 switchport mode access switchport access vlan 8 ! interface gigabitethernet1/3 switchport mode access switchport access vlan 8 switchport voice vlan 9
    B. interface gigabitethernet1/1 switchport mode access switchport access vlan 8 ! interface gigabitethernet1/3 switchport mode trunk switchport trunk vlan 8 switchport voice vlan 9
    C. interface gigabitethernet1/1 switchport mode access switchport access vlan 9 ! interface gigabitethernet1/3 switchport mode trunk switchport trunk vlan 8 switchport trunk vlan 9
    D. interface gigabitethernet1/1 switchport mode access switchport access vlan 8 ! interface gigabitethernet1/3 switchport mode access switchport voice vlan 8 switchport access vlan 9

  • Question 939:

    Which switch technology establishes a network connection immediately when it is plugged in?

    A. PortFast
    B. BPDU guard
    C. UplinkFast
    D. BackboneFast

  • Question 940:

    When a switch receives a frame from an unknown source MAC address, which action does the switch take with the frame?

    A. It sends the frame to ports within the CAM table identified with an unknown source MAC address.
    B. It floods the frame out all interfaces, including the interface it was received on.
    C. It associates the source MAC address with the LAN port on which it was received and saves it to the MAC address table.
    D. It attempts to send the frame back to the source to ensure that the source MAC address is still available for transmissions.

Related Exams:

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Cisco exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 200-301 exam preparations and Cisco certification application, do not hesitate to visit our Vcedump.com to find your solutions here.