Cisco 200-301 Online Practice Questions and Exam Preparation

Cisco 200-301 Online Questions & Answers

• Question 871:

  Refer to the exhibit.

  

  Which interface is chosen to forward traffic to the host at 192.168.0.55?

  A. GigabitEthernet0/3
  B. Null0
  C. GigabitEthernet0/1
  D. GigabitEthernet0/2
  C. GigabitEthernet0/1

• Question 872:

  Refer to the exhibit.

  

  Which switch in this configuration will be elected as the root bridge?

  SW1 0:B4:86:22:42:37 SW2 0:0B:15:22:05:97 SW3 0C:0B:15:1A:3C:9D SW4 0:B0:18:A1:B3:19

  A. SW1
  B. SW2
  C. SW3
  D. SW4
  C. SW3

• Question 873:

  Which EtherChannel mode must be configured when using LAG on a WLC?

  A. on
  B. passive
  C. active
  D. auto
  A. on

  ---

  LAG requires the EtherChannel to be configured for 'mode on' on both the controller and the Catalyst switch.

• Question 874:

  Which step in the link-state routing process is described by a router sending Hello packets out all of the OSPF- enabled interfaces?

  A. electing the designated router
  B. establishing neighbor adjacencies
  C. injecting the default route
  D. exchanging link-state advertisements
  B. establishing neighbor adjacencies

• Question 875:

  Which two pieces of information can you determine from the output of the show ntp status command? (Choose two.)

  A. whether the NTP peer is statically configured
  B. the IP address of the peer to which the clock is synchronized
  C. the configured NTP servers
  D. whether the clock is synchronized
  E. the NTP version number of the peer
  B. the IP address of the peer to which the clock is synchronized
  D. whether the clock is synchronized

  ---

  Below is the output of the "show ntp status" command. From this output we learn that R1 has a stratum of 10 and it is getting clock from 10.1.2.1.

  

• Question 876:

  Refer to the exhibit.

  

  According to the output, which parameter set is validated using the routing table of R7?

  A. R7 is missing a gateway of last resort. R7 is receiving routes that were redistributed in EIGRP. R7 will forward traffic destined to 10.90.8.0/24.
  B. R7 has a gateway of last resort available. R7 is receiving routes that were redistributed from BGP. R7 will drop traffic destined to 10.90.8.0/24.
  C. R7 is missing a gateway of last resort. R7 is receiving routes that were redistributed from BGP. R7 will forward traffic destined to 10.90.8.0/24.
  D. R7 has a gateway of last resort available. R7 is receiving routes that were redistributed in EIGRP. R7 will drop traffic destined to 10.90.8.0/24.
  D. R7 has a gateway of last resort available. R7 is receiving routes that were redistributed in EIGRP. R7 will drop traffic destined to 10.90.8.0/24.

  ---

  EX = redistributed in EIGRP. We don't know for sure from what source these routes were redistributed.

• Question 877:

  A network engineer is configuring a switch so that it is remotely reachable via SSH. The engineer has already configured the host name on the router. Which additional command must the engineer configure before entering the command to generate the RSA key?

  A. password password
  B. ip ssh authentication-retries 2
  C. ip domain-name domain
  D. crypto key generate rsa modulus 1024
  C. ip domain-name domain

  ---

  https://www.cisco.com/c/en/us/solutions/small-business/resource-center/networking/how-to-setup-network-switch.html

• Question 878:

  Refer to the exhibit.

  

  A network engineer started to change default settings on SW1 to allow remote access and has entered the following in the configuration mode:

  SW1#(config)#line vty 0 15 SW1#(config-line)#password Labtest32!

  Which set of commands are needed to allow only SSH access and hide passwords in the running configuration?

  A. SW1(config-line)#login local SW1(config-line)#exit SW1(config)#enable secret test!2E
  B. SW1(config-line)#exit SW1(config)#aaa new-model
  C. SW1(config-line)#login local SW1(config-line)#exit SW1(config)#crypto key generate rsa
  D. SW1(config-line)#transport input ssh SW1(config-line)#exit SW1(config)#service password-encryption
  D. SW1(config-line)#transport input ssh SW1(config-line)#exit SW1(config)#service password-encryption

  ---

  transport input ssh: This command ensures that only SSH connections are allowed to the device (disabling Telnet access).

• Question 879:

  DRAG DROP

  Drag and drop the benefits of a Cisco Wireless Lan Controller from the left onto the correct examples on the right.

  Select and Place:

  

  

• Question 880:

  What is the difference between controller-based networks and traditional networks as they relate to control-plane and/or data-plane functions?

  A. Controller-based networks centralize all important data-plane functions, and traditional networks distribute data-plane functions.
  B. Traditional networks centralize all important control-plane functions, and controller-based networks distribute control-plane functions.
  C. Traditional networks centralize all important data-plane functions, and controller-based networks distribute data-plane functions.
  D. Controller-based networks centralize all important control-plane functions, and traditional networks distribute control-plane functions.
  D. Controller-based networks centralize all important control-plane functions, and traditional networks distribute control-plane functions.