Cisco 200-301 Online Practice Questions and Exam Preparation

Cisco 200-301 Online Questions & Answers

• Question 731:

  Refer to the exhibit. An engineer is updating the R1 configuration to connect a new server to the management network. The PCs on the management network must be blocked from pinging the default gateway of the new server. Which command must be configured on R1 to complete the task?

  

  A. R1(config)#lp route 172.16.2.2 255.255.255.248 gi0/1
  B. R1(config)#jp route 172.16.2.2 255.255.255.255 gi0/0
  C. R1(config>#ip route 172.16.2.0 255.255.255.0 192.168.1.15
  D. R1(conflg)#ip route 172.16.2.0 255.255.255.0 192.168.1.5
  B. R1(config)#jp route 172.16.2.2 255.255.255.255 gi0/0

• Question 732:

  In which situation is private IPv4 addressing appropriate for a new subnet on the network of an organization?

  A. There is limited unique address space, and traffic on the new subnet will stay local within the organization.
  B. The network has multiple endpoint listeners, and it is desired to limit the number of broadcasts.
  C. Traffic on the subnet must traverse a site-to-site VPN to an outside organization.
  D. The ISP requires the new subnet to be advertised to the internet for web services.
  A. There is limited unique address space, and traffic on the new subnet will stay local within the organization.

• Question 733:

  Which two encoding methods are supported by REST APIs? (Choose two.)

  A. SGML
  B. YAML
  C. XML
  D. JSON
  E. EBCDIC
  C. XML
  D. JSON

  ---

  The Application Policy Infrastructure Controller (APIC) REST API is a programmatic interface that uses REST architecture. The API accepts and returns HTTP (not enabled by default) or HTTPS messages that contain JavaScript Object Notation (JSON) or Extensible Markup Language (XML) documents.

  Reference: https://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus1000/sw/5_x/rest_api_config/b_Cisco_N1KV_VMware_REST_API_Config_5x/b_Cisco_N1KV_VMware_REST_API_Config_5x_chapter_010.pdf

• Question 734:

  What are two benefits that the UDP protocol provide for application traffic? (Choose two.)

  A. UDP traffic has lower overhead than TCP traffic
  B. UDP provides a built-in recovery mechanism to retransmit lost packets
  C. The CTL field in the UDP packet header enables a three-way handshake to establish the connection
  D. UDP maintains the connection state to provide more stable connections than TCP
  E. The application can use checksums to verify the integrity of application data
  A. UDP traffic has lower overhead than TCP traffic
  E. The application can use checksums to verify the integrity of application data

• Question 735:

  Which result occurs when PortFast is enabled on an interface that is connected to another switch?

  A. Root port choice and spanning tree recalculation are accelerated when a switch link goes down.
  B. After spanning tree converges, PortFast shuts down any port that receives BPDUs.
  C. VTP is allowed to propagate VLAN configuration information from switch to switch automatically.
  D. Spanning tree may fail to detect a switching loop in the network that causes broadcast storms.
  D. Spanning tree may fail to detect a switching loop in the network that causes broadcast storms.

  ---

  Enabling the PortFast feature causes a switch or a trunk port to enter the STP forwarding-state immediately or upon a linkup event, thus bypassing the listening and learning states. Note: To enable portfast on a trunk port you need the trunk keyword "spanning-tree portfast trunk"

• Question 736:

  Which AP mode serves as the primary hub in a point-to-multipoint network topology?

  A. Flex Connect
  B. bridge
  C. SE-Connect
  D. local
  B. bridge

  ---

  In bridge mode, an Access Point (AP) acts as a hub or central node in a wireless bridge topology. In a point-to-multipoint setup, one AP serves as the central bridge (the primary hub) connecting multiple remote locations (client bridges). This mode is often used in scenarios where a wireless connection is needed between different buildings or distant locations without requiring a wired connection.

• Question 737:

  What is a characteristic of private IPv4 addressing?

  A. is used when the ISP requires the new subnet to be advertised to the internet for web services
  B. provides unlimited address ranges
  C. is used when the network has multiple endpoint listeners
  D. is used on hosts that communicate only with other internal hosts
  D. is used on hosts that communicate only with other internal hosts

• Question 738:

  DRAG DROP

  Drag and drop the descriptions of file-transfer protocols from the left onto the correct protocols on the right.

  Select and Place:

  

  

• Question 739:

  What is the primary purpose of a console port on a Cisco WLC?

  A. in-band management via an asynchronous transport
  B. in-band management via an IP transport
  C. out-of-band management via an asynchronous transport
  D. out-of-band management via an IP transport
  C. out-of-band management via an asynchronous transport

  ---

  The console port on a Cisco Wireless LAN Controller (WLC) is used for out-of-band management via an asynchronous transport. The console port provides a direct, physical connection to the WLC and can be used for initial configuration, troubleshooting, and recovery in case of network connectivity issues. In contrast, in-band management refers to the management of the WLC using the same network infrastructure that is used for user traffic. This is typically done via an IP transport, such as SSH or HTTPS, and allows administrators to manage the WLC remotely.

• Question 740:

  Which type of address is the public IP address of a NAT device?

  A. outside global
  B. outsdwde local
  C. inside global
  D. insride local
  E. outside public
  F. inside public
  C. inside global

  ---

  NAT use four types of addresses:

  1. Inside local address - The IP address assigned to a host on the inside network. The address is usually not an IP address assigned by the Internet Network Information Center (InterNIC) or service provider. This address is likely to be an RFC 1918 private address.

  2. Inside global address - A legitimate IP address assigned by the InterNIC or service provider that represents one or more inside local IP addresses to the outside world.

  3. Outside local address - The IP address of an outside host as it is known to the hosts on the inside network.

  4. Outside global address - The IP address assigned to a host on the outside network. The owner of the host assigns this address.