Cisco 200-301 Online Practice Questions and Exam Preparation

Cisco 200-301 Online Questions & Answers

• Question 751:

  In which two formats can the IPv6 address fd15:0db8:0000:0000:0700:0003:400F:572B be written? (Choose two.)

  A. fd15:0db8:0000:0000:700:3:400F:527B
  B. fd15::db8::700:3:400F:527B
  C. fd15:db8:0::700:3:4F:527B
  D. fd15:0db8::7:3:4F:527B
  E. fd15:db8::700:3:400F:572B
  A. fd15:0db8:0000:0000:700:3:400F:527B
  E. fd15:db8::700:3:400F:572B

• Question 752:

  Refer to the exhibit. When router R1 is sending traffic to IP address 10.56.192.1, which interface or next hop address does it use to route the packet?

  

  A. 10.56.0.1
  B. 0.0.0.0/0
  C. Vlan57
  D. 10.56.128.19
  A. 10.56.0.1

• Question 753:

  What does a router do when configured with the default DNS lookup settings, and a URL is entered on the CLI?

  A. initiates a ping request to the URL
  B. prompts the user to specify the desired IP address
  C. continuously attempts to resolve the URL until the command is cancelled
  D. sends a broadcast message in an attempt to resolve the URL
  D. sends a broadcast message in an attempt to resolve the URL

• Question 754:

  Which combination of methods satisfies the minimum security requirements when a new multifactor authentication solution is deployed?

  A. password of 8 to 15 characters and personal 12-diglt PIN
  B. authorized USB dongle and mobile phone
  C. fingerprint scanning and facial recognition
  D. complex password and time-based one-time password
  D. complex password and time-based one-time password

• Question 755:

  A default route must be configured to temporarily use a local broadband modem with the IP address of 192.168.1.1 until a WAN circuit is installed.

  The WAN circuit will use an external routing protocol that exchanges network prefixes between two separate autonomous systems on the Internet.

  Only a default route will be received by the ISP

  Which configuration must be applied to allow the new WAN circuit to take precedence when It Is In place?

  A. Ip route 0.0.0.0 0.0.0.0 192.168.1.1
  B. Ip route 0.0.0.0 0.0.0.0 192.168.1.1 25
  C. Ip route 0.0.0.0 0.0.0.0 192.168.1.1 track 1
  D. Ip route 0.0.0.0 0.0.0.0 192.168.1.1 20
  B. Ip route 0.0.0.0 0.0.0.0 192.168.1.1 25

• Question 756:

  Which value is used to determine the active router in an HSRP default configuration?

  A. Router loopback address
  B. Router IP address
  C. Router priority
  D. Router tracking number
  B. Router IP address

  ---

  Q. If there is no priority configured for a standby group, what determines which router is active?

  A. The priority field is used to elect the active router and the standby router for the specific group. In the case of an equal priority, the router with the highest IP address for the respective group is elected as active. Furthermore, if there are more than two routers in the group, the second highest IP address determines the standby router and the other router/routers are in the listen state.

• Question 757:

  DRAG DROP

  Drag and chop the TCP/IP protocols from the left onto their primary transmission protocols on the right.

  Select and Place:

  

  

• Question 758:

  Refer to the exhibit.

  

  A public IPv6 address must be configured for internet access. Which command must be configured on the R2 WAN interface to the service provider?

  A. ipv6 address fe80::/10
  B. ipv6 address 2001:db8:433:37:7710:ffff:ffff:ffff/64 anycast
  C. ipv6 address 2001:db8:123:45::4/64
  D. ipv6 address fe80::260:3EFF:FE11:6770 link-local
  C. ipv6 address 2001:db8:123:45::4/64

• Question 759:

  The clients and DHCP server reside on different subnets. Which command must be used to forward requests and replies between clients on the 10.10.0.1/24 subnet and the DHCP server at 192.168.10.1?

  A. ip route 192.168.10.1
  B. ip dhcp address 192.168.10.1
  C. ip default-gateway 192.168.10.1
  D. ip helper-address 192.168.10.1
  D. ip helper-address 192.168.10.1

  ---

  To forward DHCP requests and replies between clients on the 10.10.0.1/24 subnet and the DHCP server at 192.168.10.X, you would need to configure IP Helper Address on the router or layer 3 switch that is acting as the gateway for the 10.10.0.1/24 subnet.

• Question 760:

  Refer to the exhibit. The link between PC1 and the switch is up. but it is performing poorly. Which interface condition is causing the performance problem?

  

  A. There is a duplex mismatch on the interface
  B. There is an issue with the fiber on the switch interface.
  C. There is a speed mismatch on the interface.
  D. There is an interface type mismatch
  A. There is a duplex mismatch on the interface