Cisco 200-301 Online Practice Questions and Exam Preparation

Cisco 200-301 Online Questions & Answers

• Question 1311:

  Refer to the exhibit.

  

  An engineer deploys a topology in which R1 obtains its IP configuration from DHCP. If the switch and DHCP server configurations are complete and correct. Which two sets of commands must be configured on R1 and R2 to complete the task? (Choose two)

  A. R1(config)# interface fa0/0 R1(config-if)# ip helper-address 198.51.100.100
  B. R2(config)# interface gi0/0 R2(config-if)# ip helper-address 198.51.100.100
  C. R1(config)# interface fa0/0 R1(config-if)# ip address dhcp R1(config-if)# no shutdown
  D. R2(config)# interface gi0/0 R2(config-if)# ip address dhcp
  E. R1(config)# interface fa0/0 R1(config-if)# ip helper-address 192.0.2.2
  B. R2(config)# interface gi0/0 R2(config-if)# ip helper-address 198.51.100.100
  C. R1(config)# interface fa0/0 R1(config-if)# ip address dhcp R1(config-if)# no shutdown

• Question 1312:

  Why would a network administrator implement the HSRP protocol?

  A. To provide network redundancy in the case of a router failure
  B. To use an open standard protocol that is configured on Cisco and third-party routers
  C. To allow hosts in a network to use the same default gateway virtual IP when load- balancing traffic
  D. To allow clients to be configured with multiple default gateway IPs
  A. To provide network redundancy in the case of a router failure

• Question 1313:

  Which protocol prompts the Wireless LAN Controller to generate its own local web administration SSL certificate for GUI access?

  A. HTTPS
  B. RADIUS
  C. TACACS+
  D. HTTP
  A. HTTPS

  ---

  You can protect communication with the GUI by enabling HTTPS. HTTPS protects HTTP browser sessions by using the Secure Sockets Layer (SSL) protocol. When you enable HTTPS, the controller generates its own local web administration SSL certificate and automatically applies it to the GUI. You also have the option of downloading an externally generated certificate. Reference: https://www.cisco.com/c/en/us/td/docs/wireless/controller/8-0/configuration-guide/b_cg80/b_cg80_chapter_011.html

• Question 1314:

  Refer to the exhibit. Users need to connect to the wireless network with IEEE 802. 11r-compatible devices. The connection must be maintained as users travel between floors or to other areas in the building. What must be the configuration of the connection?

  

  A. Select the WPA Policy option with the CCKM option.
  B. Disable AES encryption.
  C. Enable Fast Transition and select the FT 802.1x option.
  D. Enable Fast Transition and select the FT PSK option.
  D. Enable Fast Transition and select the FT PSK option.

• Question 1315:

  What criteria is used first during the root port selection process?

  A. local port ID
  B. lowest path cost to the toot bridge
  C. lowest neighbor's bridge ID
  D. lowest neighbor's port ID
  B. lowest path cost to the toot bridge

• Question 1316:

  Which feature can you implement to reserve bandwidth for VoIP calls across the call path?

  A. round robin
  B. CBWFQ
  C. PQ
  D. RSVP
  D. RSVP

• Question 1317:

  Which command must you enter to guarantee that an HSRP router with higher priority becomes the HSRP primary router after it is reloaded?

  A. standby 10 preempt
  B. standby 10 version 1
  C. standby 10 priority 150
  D. standby 10 version 2
  A. standby 10 preempt

  ---

  The "preempt" command enables the HSRP router with the highest priority to immediately become the active router.

• Question 1318:

  Refer to the exhibit.

  

  An engineer is asked to config router R1 so that it forms an OSPF single-area neighbor relationship with R2.

  Which command sequence must be implemented to configure the router?

  A. router ospf 10 network 10.0.0.0 0.0.0.3 area 0 network 10.0.2.0 0.0.0.255 area 0
  B. router ospf 10 network 10.0.0.0 0.0.0.3 area 0 network 10.0.1.0 0.0.0.255 area 0
  C. router ospf 10 network 10.0.0.0 0.0.0.3 area 0 network 10.0.2.0 255.255.255.0 area 0
  D. router ospf 10 network 10.0.0.0 0.0.0.252 area 0 network 10.0.1.0 0.0.0.255 area 0
  B. router ospf 10 network 10.0.0.0 0.0.0.3 area 0 network 10.0.1.0 0.0.0.255 area 0

  ---

  Configure route to 10.0.0.0/30 with wildcard 0.0.0.3 Confugure route to 10.0.1.0/24 with wildcard 0.0.0.255 router ospf 10 network 10.0.0.0 0.0.0.3 area0 network 10.0.1.0 0.0.0.255 area0

• Question 1319:

  Refer to the exhibit.

  

  Which switch in this configuration will be elected as the root bridge?

  SW1: 0c:d4:86:82:87:37 SW2: 0c:d0:14:2c:05:97 SW3: 0c:0d:a2:1a:3c:9d SW4: 0c:0d:12:a1:b3:19

  A. SW1
  B. SW2
  C. SW3
  D. SW4
  D. SW4

• Question 1320:

  DRAG DROP

  Drag and drop the management connection types from the left onto the definitions on the right.

  Select and Place: