1. Home
  2. Cisco
  3. 200-301

Cisco 200-301 Online Practice Questions and Exam Preparation

200-301 Exam Details

  • Exam Code
    :200-301
  • Exam Name
    :Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1
  • Certification
    :CCNA
  • Vendor
    :Cisco
  • Total Questions
    :1716 Q&As
  • Last Updated
    :Jun 01, 2026

Cisco 200-301 Online Questions & Answers

  • Question 1171:

    CCNA Lab simulation

    Physical connectivity is implemented between the two Layer 2 switches, and the network connectivity between them must be configured:

    1.Configure an LACP EtherChannel and number it as 1; configure it between switches SW1 and SVV2 using interfaces Ethernet0/0 and Ethernet0/1 on both sides. The LACP mode must match on both ends

    2.Configure the EtherChannel as a trunk link.

    3.Configure the trunk link with 802.1 q tags.

    4.Configure the native VLAN of the EtherChannel as VLAN 15.

    A. Check the Explanation below
    B. Place Holder
    C. Place Holder
    D. Place Holder

  • Question 1172:

    Refer to the exhibit.

    What is the metric associated with the route used to forward a packet received by the router destined for the IP address 172.20.0.222?

    A. 100
    B. 101
    C. 20
    D. 110

  • Question 1173:

    Refer to the exhibit.

    Which switch in this configuration will be elected as the root bridge?

    SW1 0:0A:05:22:05:97 SW2 0:4A:82:07:57:58 SW3 0C:0A:A8:1A:3C:9D SW4 0:0A:18:A1:B3:19

    A. SW1
    B. SW2
    C. SW3
    D. SW4

  • Question 1174:

    Refer to Exhibit.

    Which configuration must be applied to the router that configures PAT to translate all addresses in VLAN 200 while allowing devices on VLAN 100 to use their own IP addresses?

    A. Router1(config)#access-list 99 permit 192.168.100.32 0.0.0.31 Router1(config)#ip nat inside source list 99 interface gi1/0/0 overload Router1(config)#interface gi2/0/1.200 Router1(config)#ip nat inside Router1(config)#interface gi1/0/0 Router1(config)#ip nat outside
    B. Router1(config)#access-list 99 permit 192.168.100.0 0.0.0.255 Router1(config)#ip nat inside source list 99 interface gi1/0/0 overload Router1(config)#interface gi2/0/1.200 Router1(config)#ip nat inside Router1(config)#interface gi1/0/0 Router1(config)#ip nat outside
    C. Router1(config)#access-list 99 permit 209.165.201.2 255.255.255.255 Router1(config)#ip nat inside source list 99 interface gi1/0/0 overload Router1(config)#interface gi2/0/1.200 Router1(config)#ip nat inside Router1(config)#interface gi1/0/0 Router1(config)#ip nat outside
    D. Router1(config)#access-list 99 permit 209.165.201.2 0.0.0.0 Router1(config)#ip nat inside source list 99 interface gi1/0/0 overload Router1(config)#interface gi2/0/1.200 Router1(config)#ip nat inside Router1(config)#interface gi1/0/0 Router1(config)#ip nat outside

  • Question 1175:

    Refer to the exhibit.

    All VLANs are present in the VLAN database.

    Which command sequence must be applied to complete the configuration?

    A. interface FastEthernet0/1 switchport trunk native vlan 10 switchport trunk allowed vlan 10,15
    B. interface FastEthernet0/1 switchport mode trunk switchport trunk allowed vlan 10,15
    C. interface FastEthernet0/1 switchport mode access switchport voice vlan 10
    D. interface FastEthernet0/1 switchport trunk allowed vlan add 10 vlan 10 private-vlan isolated

  • Question 1176:

    When the LAG configuration is updated on a Cisco WLC, which additional task must be performed when changes are complete?

    A. Reboot the WLC.
    B. Flush all MAC addresses from the WLC.
    C. Re-enable the WLC interfaces.
    D. Re-associate the WLC with the access point.

  • Question 1177:

    Refer to the exhibit.

    Which command provides this output?

    A. show ip route
    B. show cdp neighbor
    C. show ip interface
    D. show interface

  • Question 1178:

    Refer to the exhibit.

    What is the correct next hop for router R1 to reach IP addresses 192.168.2.86 and 10.20.1.50?

    A. 172.16.1.4
    B. 172.16.1.1
    C. 172.16.1.2
    D. 172.16.1.3

  • Question 1179:

    DRAG DROP

    Drag and drop the device behaviors from the left onto the matching HSRP state on the right.

    Select and Place:

  • Question 1180:

    A network engineer is replacing the switches that belong to a managed-services client with new Cisco Catalyst switches. The new switches will be configured for updated security standards, including replacing Telnet services with encrypted connections and doubling the modulus size from 1024. Which two commands must the engineer configure on the new switches? (Choose two.)

    A. crypto key generate rsa general-keys modulus 1024
    B. transport input all
    C. crypto key generate rsa usage-keys
    D. crypto key generate rsa modulus 2048
    E. transport Input ssh

Related Exams:

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Cisco exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 200-301 exam preparations and Cisco certification application, do not hesitate to visit our Vcedump.com to find your solutions here.