1. Home
  2. Cisco
  3. 200-301

Cisco 200-301 Online Practice Questions and Exam Preparation

200-301 Exam Details

  • Exam Code
    :200-301
  • Exam Name
    :Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1
  • Certification
    :CCNA
  • Vendor
    :Cisco
  • Total Questions
    :1716 Q&As
  • Last Updated
    :Jun 01, 2026

Cisco 200-301 Online Questions & Answers

  • Question 1001:

    DRAG DROP

    Refer to the exhibit.

    An engineer is configuring the router to provide static NAT for the webserver Drag and drop the configuration commands from the left onto the letters that correspond to its position in the configuration on the right.

    Select and Place:

  • Question 1002:

    Refer to the exhibit.

    An OSPF neighbor relationship must be configured using these guidelines:

    1. R1 is only permitted to establish a neighbor with R2
    2. R1 will never participate in DR elections
    3. R1 will use a router-id of 101.1.1.

    Which configuration must be used?

    A. interface FastEthernet0/0 ip address 10.100.1.1 255.255.255.252 ip ospf priority 0 ip access-group 102 in router ospf 10 log-adjacency-changes network 10.1.1.1 0.0.0.0 area 0 network 10.100.1.0 0.0.0.3 area 0 router-id 10.1.1.1 access-list 102 permit 89 host 10.100.1.2 host 224.0.0.5 access-list 102 deny 89 any any access-list 102 permit ip any any
    B. interface Loopback0 ip address 10.1.1.1 255.255.255.255 interface FastEthernet0/0 ip address 10.100.1.1 255.255.255.252 ip ospf priority 100 ip access-group 102 in router ospf 10 log-adjacency-changes network 10.1.1.1 0.0.0.0 area 0 network 10.100.1.0 0.0.0.3 area 0 router-id 10.1.1.1 access-list 102 permit 88 host 10.100.1.2 host 224.0.0.5 access-list 102 deny 88 any any access-list 102 permit ip any any
    C. interface FastEthernet0/0 ip address 10.100.1.1 255.255.255.252 ip ospf priority 100 ip access-group 102 in router ospf 10 log-adjacency-changes network 10.1.1.1 0.0.0.0 area 0 network 10.100.1.0 0.0.0.3 area 0 router-id 10.1.1.1 access-list 102 permit 89 host 10.100.1.2 host 224.0.0.5 access-list 102 deny 89 any any access-list 102 permit ip any any
    D. interface Loopback0 ip address 10.1.1.1 255.255.255.255 interface FastEthernet0/0 ip address 10.100.1.1 255.255.255.252 ip ospf priority 0 ip access-group 102 in router ospf 10 log-adjacency-changes network 10.1.1.1 0.0.0.0 area 0 network 10.100.1.0 0.0.0.3 area 0 router-id 10.1.1.1 access-list 102 permit 88 host 10.100.1.2 host 224.0.0.5 access-list 102 deny 88 any any access-list 102 permit ip any any

  • Question 1003:

    What is used to identify spurious DHCP servers?

    A. DHCPACK
    B. DHCPREQUEST
    C. DHCPOFFER
    D. DHCPDISCOVER

  • Question 1004:

    What is the effect when loopback interfaces and the configured router ID are absent during the OSPF Process configuration?

    A. No router ID is set, and the OSPF protocol does not run.
    B. The highest up/up physical interface IP address is selected as the router ID.
    C. The lowest IP address is incremented by 1 and selected as the router ID.
    D. The router ID 0.0.0.0 is selected and placed in the OSPF process.

  • Question 1005:

    What are two enhancements that OSPFv3 supports over OSPFv2? (Choose two.)

    A. It requires the use of ARP.
    B. It can support multiple IPv6 subnets on a single link.
    C. It supports up to 2 instances of OSPFv3 over a common link.
    D. It routes over links rather than over networks.

  • Question 1006:

    Refer to the exhibit. On R1 which routing protocol is in use on the route to 192.168.10.1?

    A. RIP
    B. OSPF
    C. IGRP
    D. EIGRP

  • Question 1007:

    Refer to the exhibit.

    Shortly after SiteA was connected to SiteB over a new single-mode fiber path users at SiteA report intermittent connectivity issues with applications hosted at SiteB What is the cause of the intermittent connectivity issue?

    A. Interface errors are incrementing
    B. An incorrect SFP media type was used at SiteA
    C. High usage is causing high latency
    D. The sites were connected with the wrong cable type

  • Question 1008:

    What are two reasons to implement DHCP in a network? (Choose two.)

    A. manually control and configure IP addresses on network devices
    B. control the length of time an IP address is used by a network device
    C. reduce administration time in managing IP address ranges for clients
    D. dynamic control over the best path to reach an IP address
    E. access a website by name instead of by IP address

  • Question 1009:

    Reter to the exhibit

    The iPv6 address for the LAN segment on router R2 must be configured using the EUi-4 format. Which address must be used?

    A. ipv6 address 2001:DB8:D8D2:1009:10A0:ABFF:FECC:1 eui-64
    B. ipv6 address 2001:DB8:D8D2:1009:1230:ABFF:FECC:1 eui-64
    C. ipv6 address 2001:DB8:D8D2:1009:4331:89FF:FF23:9 eui-64
    D. ipv6 address 2001:DB8:D8D2:1009:12A0:AB34:FFCC:1 eui-64

  • Question 1010:

    DRAG DROP

    Drag and drop the RF terms from the left onto the corresponding statements on the right.

    Select and Place:

Related Exams:

Tips on How to Prepare for the Exams

Nowadays, the certification exams become more and more important and required by more and more enterprises when applying for a job. But how to prepare for the exam effectively? How to prepare for the exam in a short time with less efforts? How to get a ideal result and how to find the most reliable resources? Here on Vcedump.com, you will find all the answers. Vcedump.com provide not only Cisco exam questions, answers and explanations but also complete assistance on your exam preparation and certification application. If you are confused on your 200-301 exam preparations and Cisco certification application, do not hesitate to visit our Vcedump.com to find your solutions here.