Cisco 200-105 Online Practice Questions and Exam Preparation

Cisco 200-105 Online Questions & Answers

• Question 501:

  After you configure a GRE tunnel between two networks, the tunnel comes up normally, but workstations on each side of the tunnel cannot communicate.

  Which reason for the problem is most likely true?

  A. The tunnel source address is incorrect.
  B. The tunnel destination address is incorrect.
  C. The route between the networks is undefined.
  D. The IP MTU is incorrect.
  E. The distance configuration is missing.
  D. The IP MTU is incorrect.

• Question 502:

  Which technology can provide security when connection multiple sites across the internet?

  A. EBGP
  B. DMVPN
  C. Site-to-site vpn
  D. MPLS
  B. DMVPN

• Question 503:

  Given an IP address 172.16.28.252 with a subnet mask of 255.255.240.0, what is the correct network address?

  A. 172.16.16.0
  B. 172.16.0.0
  C. 172.16.24.0
  D. 172.16.28.0
  A. 172.16.16.0

• Question 504:

  After you configure a new IP SLA, you notice that it is failing to run or generate statistics. Which step do you take first to identify the problem?

  A. Use the debug ip sla trace command on the device to troubleshoot.
  B. Add the verify-data command to the IP SLA configuration.
  C. Add procative threshold conditions to the IP SLA to facilitate troubleshooting.
  D. Use the debug ip sla error command on the device to troubleshoot.
  D. Use the debug ip sla error command on the device to troubleshoot.

• Question 505:

  Which two data integrity algorithms are commonly used in VPN solutions? (Choose two.)

  A. DH1
  B. DH2
  C. HMAC-MD5
  D. HMAC-SHA-1
  E. RSA
  C. HMAC-MD5
  D. HMAC-SHA-1

• Question 506:

  Which option describes the purpose of traffic policing?

  A. It prioritizes routing protocol traffic.
  B. It remarks traffic that is below the CIR.
  C. It drops traffic that exceeds the CIR.
  D. It queues and then transmits traffic that exceeds the CIR.
  C. It drops traffic that exceeds the CIR.

  ---

  Traffic policing allows you to control the maximum rate of traffic transmitted or received on an interface. Traffic policing is often configured on interfaces at the edge of a network to limit traffic into or out of the network. In most Traffic Policing configurations, traffic that falls within the rate parameters is transmitted, whereas traffic that exceeds the parameters is dropped or transmitted with a different priority.

• Question 507:

  Which three commands do you use to verify that IPSec over a GRE tunnel is working properly? (Choose three.)

  A. Clear Crypto isakmp
  B. PPP encrypt mppe auto
  C. Show crypto engine connections active
  D. Show crypto ipsec sa
  E. Show crypto isakmp sa
  F. Debug crypto isakmp
  D. Show crypto ipsec sa
  E. Show crypto isakmp sa
  F. Debug crypto isakmp

• Question 508:

  Which value must you configure on a device before EIGRP for IPV6 can start running?

  A. Process ID
  B. Router ID
  C. Public IP Address
  D. Loopback interface
  B. Router ID

• Question 509:

  Which three fields can be marked with QoS? (Choose three.)

  A. Header checksum
  B. IP precedence
  C. DSCP
  D. Total length
  E. Discard Class
  F. TTL
  B. IP precedence
  C. DSCP
  E. Discard Class

• Question 510:

  What is the default DTP mode on a switch port?

  A. Desirable
  B. Auto
  C. Nonegotiate
  D. On
  E. Off
  B. Auto