NetApp NS0-504 Online Practice Questions and Exam Preparation

NetApp NS0-504 Online Questions & Answers

• Question 131:

  Which command do you use to see the rate of change between two successive Snapshot copies in a flexible volume in Data ONTAP?

  A. snap diff
  B. snap calculate
  C. snap delta
  D. snap space
  C. snap delta

• Question 132:

  What is the significance of using a specific LUN type when creating LUNs manually on a NetApp storage system?

  A. The LUNs offset, size of the prefix and suffix is determined by the LUN type, which differs for different operating systems.
  B. The LUN types are merely for administrative ease of use and the LUN types can be changed on the fly after creation.
  C. The LUN types allow the appropriate host operating systems to use the LUN. For example, a VMware type LUN cannot be read from /written to using a Solaris host.
  D. The host operating system will panic when the "wrong" LUN type is selected on the NetApp storage system.
  A. The LUNs offset, size of the prefix and suffix is determined by the LUN type, which differs for different operating systems.

• Question 133:

  A company wants to use jumbo frames in their Ethernet network. They should set the packet size to which industry conventional value?

  A. 1200
  B. 1500
  C. 9000
  D. 12000
  C. 9000

• Question 134:

  To ensure path redundancy and load balancing you must configure each host for________.

  A. SnapDrive for Unix
  B. thin provisioning
  C. consistent igroup usage
  D. host multipathing specific to its OS type and version level
  E. jumbo frames
  D. host multipathing specific to its OS type and version level

• Question 135:

  What does NetApp recommend as best practice for zone configuration?

  A. single port zoning
  B. single initiator zoning
  C. single target zoning
  D. multiple initiator zoning
  B. single initiator zoning

• Question 136:

  The Space Guarantee option needs to be set__________ to ensure a volume cannot be affected by other volumes storage usage.

  A. None
  B. Volume
  C. Reserved
  D. Enabled
  B. Volume

• Question 137:

  A company has FC patch panels in their data center. They plan on using them to interconnect their storage controllers to the FC switches and the hosts using the storage. They have 62.5 micron cable between the patch panels. Which cable should you use on the NetApp storage controller's Target Ports to make this a supported configuration?

  A. long wave SFPs, 62.5 micron FC cable
  B. short wave SFPs, 50 micron FC cable
  C. short wave SFPs, 62.5 micron FC cable
  D. long wave SFPs, 50 micron FC cable
  C. short wave SFPs, 62.5 micron FC cable

• Question 138:

  You have connected all cables and disk shelves in a fabric-attached MetroCluster. Which command would verify that disks are connected and have dual paths?

  A. disk show
  B. sysconfig -p
  C. vol status -r
  D. storage show disk -p
  D. storage show disk -p

• Question 139:

  You want to create an automated test environment that performs a single file SnapRestore time you run the procedure, however, SnapRestore prompts you to confirm your decision to revert the file. How can you automate this step?

  A. Use the f option with the snmap restore command
  B. Enable the options snaprestore_noprimpts enable = on option.
  C. These prompts are for data protection and auditing and cannot be overridden.
  D. Enter the priv set advanced mode on the storage system and prompt will not appear.
  A. Use the f option with the snmap restore command

• Question 140:

  Which two statements apply to an entry in the /etc/exports file regarding exporting directories/qtrees and volumes? (Choose two.)

  A. Each volume must be exported separately.
  B. Exports are accessible only to hosts with names.
  C. User names used in an export must be resolvable.
  D. Exports can access multiple paths on the same volume.
  A. Each volume must be exported separately.
  D. Exports can access multiple paths on the same volume.