NetApp NS0-504 Online Practice Questions and Exam Preparation

NetApp NS0-504 Online Questions & Answers

• Question 1:

  How do you enable an FC port on a Cisco switch?

  A. no shutdown
  B. port enable on
  C. enable port on
  D. off shutdown
  A. no shutdown

• Question 2:

  Which command on a NetApp storage controller will display the average latency time on a per LUN basis every five seconds?

  A. sysstat -i 5
  B. sysstat -f 5
  C. fcp stats -i 5
  D. lun stats -i 5
  D. lun stats -i 5

• Question 3:

  In a Fibre Channel configuration, the host's HBA is referred to as the ___________, and the storage system's HBA is referred to as the __________ .

  A. initiator, target.
  B. primary, secondary.
  C. secondary, primary.
  D. target, initiator.
  A. initiator, target.

• Question 4:

  Which statement applies to the Open Systems SnapVault Free Space Estimator utility?

  A. This utility runs automatically after each transfer.
  B. This utility must be enabled on the secondary storage system.
  C. This utility determines if there is sufficient disk space available on the primary to perform an OSSV transfer.
  D. This utility determines if there is sufficient disk space available on the secondary to perform an OSSV transfer.
  C. This utility determines if there is sufficient disk space available on the primary to perform an OSSV transfer.

• Question 5:

  What is the maximum distance between a standard clustered pair at 2Bbps?

  A. 100 meters
  B. 10 meters
  C. 50 meters
  D. 500 meters
  D. 500 meters

• Question 6:

  Which two are true when creating a SyncMirror volume? (Choose two.)

  A. The disks selected for Plex 0 and Plex 1 must come from the same disk shelf.
  B. The disks selected for Plex 0 and Plex 1 must come from the same disk pools.
  C. The number of disks added must be an even number and equally divided between the two plexes.
  D. The disks are selected first on the basis of equivalent bytes per sector (bps) size, then on the basis of the size of the disk. If there is no equivalent-sized disk, Data ONTAP takes a larger capacity disk and right-sizes it.
  C. The number of disks added must be an even number and equally divided between the two plexes.
  D. The disks are selected first on the basis of equivalent bytes per sector (bps) size, then on the basis of the size of the disk. If there is no equivalent-sized disk, Data ONTAP takes a larger capacity disk and right-sizes it.

• Question 7:

  Which storage system command should you use to group initiators to allow them to be mapped to logical unit numbers (LUNs)?

  A. igroup create
  B. igroup map
  C. igroup allow
  D. igroup group
  A. igroup create

• Question 8:

  Which three NFS versions does Data ONTAP 8.1 Cluster-Mode support? (Choose three.)

  A. NFSv.0
  B. NFSv.1
  C. NFSv1.1
  D. NFSv3.0
  E. NFSv4.0
  F. NFSv4.1
  G. NFSv5.0
  D. NFSv3.0
  E. NFSv4.0
  F. NFSv4.1

• Question 9:

  Which three items are NFS resources for export? (Choose three.)

  A. aggregate
  B. directory/qtree
  C. file
  D. subnet
  E. volume
  B. directory/qtree
  C. file
  E. volume

• Question 10:

  NetApp supports multiple FC paths from the host to the NetApp storage controllers. In addition to using multiple FC switches, which other NetApp supported components should you use for this type of configuration?

  A. multipathing host software, multiple storage controllers with multiple target ports each
  B. HBA with driver and firmware, multiple storage controllers with multiple target ports each
  C. HBA with driver and firmware, multipathing host software, multiple storage controllers with multiple initiator ports each
  D. HBA with driver and firmware, multipathing host software, multiple storage controllers with multiple target ports each
  D. HBA with driver and firmware, multipathing host software, multiple storage controllers with multiple target ports each