NetApp NS0-504 Online Practice Questions and Exam Preparation

NetApp NS0-504 Online Questions & Answers

• Question 21:

  What must be defined in order to create an NFS export within Cluster-Mode?

  A. an entry in the /etc/exports file
  B. an export policy and rules under a Vserver
  C. an export policy and rules under the FreeBSD shell
  D. an export policy and rules under the node shell
  E. export rules that are associated with a LIF
  B. an export policy and rules under a Vserver

• Question 22:

  Which topology allows for guaranteed maximum network performance for iSCSI?

  A. isolated VLAN network
  B. MetroWAN network
  C. direct connect
  D. WAN network
  C. direct connect

• Question 23:

  Portsets limit host access to certain paths when they are bound to ____________.

  A. A LUN
  B. An igroup
  C. A logical interface (LIF)
  D. A physical port
  B. An igroup

• Question 24:

  Given the information shown in the diagram, Which port has a NetApp device attached to it?

  

  A. port 7
  B. port 6
  C. port 5
  D. port 3
  A. port 7

• Question 25:

  You are trying to do a single file SnapRestore for a file, but you are receiving an error message that the directory structure no longer exists. Which is the most likely explanation?

  A. Once the directory structure has been deleted, you cannot restore the file using single file SnapRestore. You must now SnapRestore the volume.
  B. Snapshot copies have been created since the original directory structure was deleted.
  C. You must recreate the directory structure before trying to restore the file.
  D. You cannot restore a file to an alternate location.
  C. You must recreate the directory structure before trying to restore the file.

• Question 26:

  Zoning by World Wide Port Name (WWPN) is deployed and a host HBA is replaced. Which zone change needs to be made?

  A. No changes are necessary.
  B. The zone configuration should be changed to include the port to which the HBA is connected.
  C. The zone configuration should be changed to include the WWPN of the new HBA; the old WWPN will be automatically dropped.
  D. The zone configuration should be changed to include the WWPN of the new HBA and to remove the WWPN of the old HBA.
  D. The zone configuration should be changed to include the WWPN of the new HBA and to remove the WWPN of the old HBA.

• Question 27:

  An FC port on a NetApp storage system running clustered Data ONTAP is connected to an FC switch. FCP is licensed on the cluster and the Vserver FCP service is created and running. The state of the FC LIF, which is bound to the port, is

  administratively up and operationally down.

  What is the likely cause?

  A. Improper FC zone configuration
  B. NPIV is not enabled on the switch
  C. Improper igroup configuration
  D. Bad cable
  B. NPIV is not enabled on the switch

• Question 28:

  Protection Manager has policies that allow for tape-based protection as well as disk-based protection.

  A. True
  B. False
  B. False

• Question 29:

  During an equipment move a Fibre Channel cable from a host to a switch is accidentally plugged into a different switch port on the FC switch. However, the host still sees the storage devices on all its paths. What are two reasons why this is possible? (Choose two.)

  A. LUN masking uses switch port numbers and not WWPNs.
  B. The host HBA WWPN is a part of a WWPN zoning scheme.
  C. The Fibre Channel address for the HBA has not changed.
  D. The WWPN Alias was n changed on the NetApp Controllers.
  B. The host HBA WWPN is a part of a WWPN zoning scheme.
  D. The WWPN Alias was n changed on the NetApp Controllers.

• Question 30:

  The quota resize command only affects existing /etc/quotas file target entries, not new quota entries.

  A. True
  B. False
  A. True