NetApp NS0-182 Online Practice Questions and Exam Preparation

NetApp NS0-182 Online Questions & Answers

• Question 131:

  A customer wants to expand their 10-node AFF A700s SAN cluster on Cisco Nexus 3132Q-V interconnect switches. The customer has six AFF A700s nodes available. In this scenario, what should you do to expand the cluster?

  A. Add two nodes to the existing cluster without exceeding the SAN cluster limit.
  B. Add six nodes to the existing cluster.
  C. Replace the switches with Cisco Nexus 5596T switches and then add the six nodes.
  D. Add an expansion module to each switch and then add the six nodes.
  D. Add an expansion module to each switch and then add the six nodes.

• Question 132:

  Which statement regarding a node-management LIF is true?

  A. The LIF can be set only on the built-in node-management port - e0M.
  B. The LIF must use two switches for redundancy purposes.
  C. The LIF can be set up on a dedicated VLAN in the data network.
  D. The LIF can be set up on a dedicated VLAN in the cluster network.
  A. The LIF can be set only on the built-in node-management port - e0M.

• Question 133:

  You are setting up a new cluster. The customer notices that there are many management ports on the cluster. The customer wants to know the purpose of the cluster management LIF. In this situation, what should you tell the customer?

  A. The cluster management LIF provides a dedicated IP address for the entire cluster and can fail over to any port in the cluster that is available in the broadcast domain.
  B. The cluster management LIF provides a dedicated IP address for managing a particular node in the cluster and is used for system maintenance.
  C. The cluster management LIF is used to carry intracluster traffic between nodes in a cluster and must be created on a 10GbE network port.
  D. The cluster management LIF provides multiple IP addresses for the entire cluster and can fail over to any cluster or intercluster ports.
  B. The cluster management LIF provides a dedicated IP address for managing a particular node in the cluster and is used for system maintenance.

• Question 134:

  In which scenario must ACP be out-of-band?

  A. when using DS4243 shelves with SATA drives and I0M6 modules
  B. when using DS4243 shelves with SATA drives and IOM3 modules
  C. when using DS4243 shelves with SSD devices and IOM12 modules
  D. when using DS212C shelves with SSD devices and IOM12 modules
  D. when using DS212C shelves with SSD devices and IOM12 modules

• Question 135:

  Which NetApp tool relies on PowerShell to produce a comprehensive handover report to the customer?

  A. Active IQ
  B. Config Advisor
  C. NetAppDocs
  D. Fusion
  C. NetAppDocs

• Question 136:

  You are asked to install an AFF A700 with two DS224C shelves fully populated. When you arrive, the customer asks you to install an additional shelf. Which shelf would you add to this cluster?

  A. a DS224C shelf fully populated with SAS drives
  B. a DS224C shelf fully populated with SATA drives
  C. a DS2246 shelf fully populated with SSD drives
  D. a DS4486 shelf fully populated with SATA drives
  C. a DS2246 shelf fully populated with SSD drives

• Question 137:

  You have created an aggregate with one RAID group on your ONTAP 9 cluster. Two disks have already failed and have not finished reconstructing. What would protect you from a third disk failure while you are still reconstructing the two failed disks?

  A. RAID-0
  B. RAID-4
  C. RAID-TEC
  D. RAID-DP
  C. RAID-TEC

• Question 138:

  What is the maximum number of data disks that a RAID-TEC RAID group has?

  A. 26
  B. 20
  C. 29
  D. 24
  C. 29

• Question 139:

  You are asked to install a new ONTAP cluster at a customer site.

  In this scenario, which ONTAP versions would you normally install? (Choose two.)

  A. the latest RC1 with the included patch level
  B. the latest GA with the included patch level
  C. the release specified by the customer
  D. the latest D release listed for the controller type
  B. the latest GA with the included patch level
  C. the release specified by the customer

• Question 140:

  Which two configurations use root-data-data partitioning? (Choose two.)

  A. FAS8080 with 1.8 TB external SAS drives
  B. AFF A800 with 3.8 TB internal NVMe SSD drives
  C. FAS2650 with 1.8 TB internal SAS drives
  D. AFF A220 with 3.8 TB internal SSD drives
  A. FAS8080 with 1.8 TB external SAS drives
  B. AFF A800 with 3.8 TB internal NVMe SSD drives