Juniper JN0-360 Online Practice Questions and Exam Preparation

Juniper JN0-360 Online Questions & Answers

• Question 161:

  What are two port modes for a Layer 2 interface? (Choose two.)

  A. access mode
  B. dual mode
  C. trunk mode
  D. tag mod
  A. access mode
  C. trunk mode

• Question 162:

  Which command would you use to verify the presence of VPN routes on a PE device?

  A. show route table bgp.l3vpn.0
  B. show route protocol bgp terse | count
  C. show route table inet.0
  D. show route route-type vpn
  A. show route table bgp.l3vpn.0

• Question 163:

  Which statement is true about link aggregation?

  A. It facilitates control plane redundancy through link aggregation
  B. It provides an active-passive failover mechanism for redundant Layer 2 links
  C. It combines multiple Ethernet interfaces into a single link-layer interface
  D. It combines multiple Ethernet interfaces into a multilink-layer interface.
  C. It combines multiple Ethernet interfaces into a single link-layer interface

• Question 164:

  Which Junos operational mode command is used to verify that load balancing is working as expected?

  A. show route all
  B. show route extensive
  C. show route balancing
  D. show route forwarding-table
  D. show route forwarding-table

• Question 165:

  You are logged into a router and have navigated to the (edit routing-options] level of the hierarchy. You have been asked to create a static route that will use 10.10.10.1 as its primary next-hop and 10.10.10.5 as its secondary next-hop. Which command correctly configures this scenario?

  A. set static route 8/8 10.10.10.1 qualified-next-hop 10.10.10.5 pref 10
  B. set static route 8/8 next-hop 10.10.10.1 secondary-next-hop 10.10.10.5 preference 10
  C. set static route 8/8 next-hop 10.10.10.1 qualified-next-hop 10.10.10.5 preference 10
  D. set static route 8/8 next-hop [10.10.10.1 10.10.10.5] pref 10
  C. set static route 8/8 next-hop 10.10.10.1 qualified-next-hop 10.10.10.5 preference 10

• Question 166:

  You have been asked to use a convention that allows for auto configuration of interface addresses. You are not allowed to use DHCPv6. What do you do?

  A. Use IPv4 with the autoconfig option under family inet.
  B. Use IPv6 in the network to configure hosts.
  C. Use a program (e.g. Vector-Wiz) to auto configure IP addresses.
  D. Use an IPv6 static configuration.
  B. Use IPv6 in the network to configure hosts.

• Question 167:

  Click the Exhibit button

  

  In an RSTP network, the root and designated ports have been elected as shown in the exhibit What will be the port type of port 1?

  A. backup port
  B. discarding port
  C. alternate port
  D. listening port
  A. backup port

• Question 168:

  Which two statements are true about IP-IP tunnels on Junos devices? (Choose two.)

  A. They support only IP traffic
  B. Tunnel endpoints use the interface ipt
  C. They add no additional overhead to packets
  D. Each tunnel interface is point-to-point
  A. They support only IP traffic
  D. Each tunnel interface is point-to-point

• Question 169:

  Click the Exhibit.

  

  You are planning the addition of a new EX3400 Series device to the network (EX- 3400-7) to service MSTI-1 and MSTI-2.

  Referring to the exhibit, which requirement must be met on EX-3400-7 for the MSTP instances to become fully operational and resilient?

  A. The MSTP revision-level must be incremented.
  B. The CIST must be extended to EX-3400-7.
  C. The MSTP configuration-name must be the same.
  D. The bridge-priority must match EX-3400-5 and EX-3400-6.
  C. The MSTP configuration-name must be the same.

• Question 170:

  How are BGP routes originated?

  A. BGP routes are created using policies associated with BGP peering sessions.
  B. BGP routes are created using IP subnet definitions at each defined BGP peer.
  C. BGP routes are created based on interface subnets used for peering sessions.
  D. BGP routes are created based on all interface subnets on all BGP routers.
  A. BGP routes are created using policies associated with BGP peering sessions.