EMC D-PSC-MN-01 Online Practice Questions and Exam Preparation

EMC D-PSC-MN-01 Online Questions & Answers

• Question 11:

  Dell Technical Support has requested a part be sent back to Dell Logistics to be studied. Which process or document musi be completed before sending the part back?

  A. WWFA
  B. DTFA
  C. DMR
  D. CDMR
  C. DMR

• Question 12:

  What accurately describes the InfiniBand cable support?

  A. Supports QSFP to QSFP cabling only
  B. Supports QSFP to QSFP cabling or QSFP to CX4 cabling
  C. Supports QSFP to CX4 cabling only
  D. Supports front-end customer external traffic
  A. Supports QSFP to QSFP cabling only

• Question 13:

  What is the maximum recommended ambient temperature for the operation of a Dell EMC PowerScale Gen 6 node?

  A. 27 degrees C (80 degrees F)
  B. 32 degrees C (89 degrees F)
  C. 35 degrees C (95 degrees F)
  D. 40 degrees C (104 degrees F)
  C. 35 degrees C (95 degrees F)

• Question 14:

  A platform engineer has connected to a Dell EMC PowerScale F600 node using a serial connection. The session is unresponsive. What action should the engineer take?

  A. Enable the serial port from the front panel menu
  B. Connect to the primary node of the pair
  C. Configure the cluster before connecting to the node
  D. Check the settings of the serial connection
  D. Check the settings of the serial connection

• Question 15:

  What type of privileges are required to perform tenant-specific administration?

  A. Zone role-based access control
  B. System root privileges
  C. System admin privileges
  D. Role-based access control
  A. Zone role-based access control

• Question 16:

  What is an important consideration when connecting Dell PowerScale Gen6 nodes to external power?

  A. Cable each node in a node pair to a different PDU.
  B. Cable all nodes to the external power feeds before connecting switch power cables.
  C. The total power load for all nodes in the rack should not exceed 100% of the branch circuit rating.
  D. Connect both cables of each node to different external power feeds.
  D. Connect both cables of each node to different external power feeds.

• Question 17:

  Which cluster interface provides the most detailed network traffic statistics and enables file and directory operations on the cluster?

  A. Web console
  B. Serial console
  C. Platform API
  D. CLI
  D. CLI

• Question 18:

  A platform engineer is connecting a new Dell EMC PowerScale F600 node to the back-end switch. How should the back-end cable be connected?

  A. From PCIe slot 3 to the back-end InfiniBand switch.
  B. From PCIe slot 1 to the back-end Ethernet switch.
  C. From PCIe slot 1 to the back-end InfiniBand switch.
  D. From PCIe slot 3 to the back-end Ethernet switch.
  B. From PCIe slot 1 to the back-end Ethernet switch.

• Question 19:

  What does a terracotta colored handle indicate on Dell PowerScale Gen6 hardware?

  A. The FRU must be replaced.
  B. The node can remain online when replacing a hardware component.
  C. The node must be shut down for maintenance procedures.
  D. The component must not be removed while hardware is online.
  D. The component must not be removed while hardware is online.

• Question 20:

  What are the required settings when using terminal emulation software to connect to a Dell EMC PowerScale Gen 5 node?

  A. Transfer Rate = 57.600, Data Bits = 8, Parity = 1, Stop Bits = 0, Flow Control = Software
  B. Transfer Rate = 115.200, Data Bits = 8, Parity = None, Stop Bits = 1, Flow Control = Hardware
  C. Transfer Rate = 57.600, Data Bits = 7, Parity = 1, Stop Bits = 8, Flow Control = Hardware
  D. Transfer Rate = 115.200, Data Bits = 7, Parity = 1, Stop Bits = 1, Flow Control = Software
  B. Transfer Rate = 115.200, Data Bits = 8, Parity = None, Stop Bits = 1, Flow Control = Hardware