Riverbed 830-01 Online Practice Questions and Exam Preparation

Riverbed 830-01 Online Questions & Answers

• Question 321:

  When enabling WCCP v2 support, what does a multicast TTL value of 1 imply?

  A. This enables WCCP v2 support
  B. The Steelhead appliance uses a multicast scope of 1 hop
  C. This enables WCCP multicast
  D. This enables WCCP unicast
  B. The Steelhead appliance uses a multicast scope of 1 hop

• Question 322:

  When configuring encrypted Lotus Notes optimization and the standard port is configured to require encryption, which of the following is true?

  A. An alternate unencrypted port must be open on the server, and a copy of the server ID file must be imported to the server side SteelHead.
  B. An alternate unencrypted port must be open on the server, and a proxy server ID file must be created on the server-side SteelHead.
  C. An encrypted port must be open on the server, and a proxy server ID file must be created on the server-side SteelHead.
  D. An encrypted port must be open on the server, and a copy of the server ID file must be imported to the server-side SteelHead.
  A. An alternate unencrypted port must be open on the server, and a copy of the server ID file must be imported to the server side SteelHead.

• Question 323:

  When deploying Interceptor appliances in a parallel cluster what feature must be disabled to ensure packet redirection upon failure?

  A. Fail-to-wire.
  B. Connection forwarding.
  C. Fail-to-block.
  D. Link State Propagation.
  E. WCCP.
  A. Fail-to-wire.

• Question 324:

  When Connection Forwarding is in use, when a neighbor fails, the default behavior of the remaining neighbor will be to:

  A. It will start to bypass traffic immediately
  B. It will start to bypass traffic only after about 30 seconds
  C. It is transparent to the outage and will continue to optimize as per normal
  D. It will cease to optimize for about 30 seconds and start to optimize again
  B. It will start to bypass traffic only after about 30 seconds

• Question 325:

  Refer to the exhibit.

  

  You configured CIFS prepopulation at Corp-A but it is not working. What is likely the cause of the issue?

  A. CIFS prepopulation requires WCCP
  B. Primary interface needs to be on a different subnet
  C. CIFS prepopulation requires a fixed-target rule
  D. The Primary interface needs to be on the LAN side of the Steelhead appliance
  E. CIFS prepopulation requires SMBv2
  D. The Primary interface needs to be on the LAN side of the Steelhead appliance

• Question 326:

  The CMC appliance version 6.1 supports which SNMP versions? (Select 3)

  A. Version 1
  B. Version 2
  C. Version 2c
  D. Version 3
  A. Version 1
  C. Version 2c
  D. Version 3

• Question 327:

  In an existing deployment, all connections appear to be unoptimized. The Current Connections page lists the connections as pass-through.

  

  The logs indicate admission control "Jan 19 18:44:56 client sport[343]: [admission_control.WARN] Pausing intercept." What are some possible ways to alleviate the problem? (Select 2)

  A. Verify that there is no SMB Signing on the server
  B. Ensure that there are no Opportunistic Lock issues
  C. Disable or reduce the connection timeout of MAPI prepopulation
  D. Investigate if there is a virus on a client trying to propagate itself
  E. Validate that NFS v2 broadcasts are enabled
  C. Disable or reduce the connection timeout of MAPI prepopulation
  D. Investigate if there is a virus on a client trying to propagate itself

• Question 328:

  A customer wants to deploy parallel Interceptor appliances. How should an Interceptor appliance be configured in relation to another parallel Interceptor appliance?

  A. Peer Interceptor
  B. As a failover buddy
  C. As a peer neighbor
  D. A and B
  E. A, B, and C
  A. Peer Interceptor

• Question 329:

  Examine the diagram below. The customer needs to optimize data center servers and also servers within the DMZ but wants to keep the SteelHead behind the firewall. Which optimization mode would support this environment?

  

  A. Hybrid mode
  B. Virtual In-path mode
  C. WCCP or Interceptor mode
  D. Out-of-path mode
  E. In-path mode
  A. Hybrid mode

• Question 330:

  The primary purpose of setting proxies (found on Networking ?Proxies) on the Interceptor is to:

  A. Allow for a Web or FTP proxy when specifying a URL on the Management Console or CLI
  B. Allow for another Interceptor to redirect on behalf of the current Interceptor
  C. Allow for Steelhead appliances to dynamically handle the load of another Steelhead appliance
  D. Allow for two Interceptor appliances to act redundantly in a serial configuration
  A. Allow for a Web or FTP proxy when specifying a URL on the Management Console or CLI